5
ENGLISH
7.
Press the “ALARM 1” button (4).
The alarm
signal symbols will start flashing on the dis-
play. Use the buttons (8) and (9) to select the
necessary alarm signal. sound signal (sym-
bol «bu») or radio (tuned station frequency
appears)
Note: If you want to select the radio as alarm
signal, preliminary tune the required radio station
(see “Radio stations reception”).
8.
If you have selected “radio” signal type, press
the «ALARM 1» button (4) and select the
alarm desired volume level using the buttons
(8) and (9).
9.
To finish the first alarm setting press the
«ALARM 1» button (4).
10.
Repeat steps 2-10 for the second alarm
«ALARM 2» (5).
Note:
–
If buttons (8) and (9) are not pressed
within 30 seconds, the unit will switch to
the current time mode.
–
Alarm operation is only possible when the
unit is connected to the mains.
Switching alarms on/off
1.
To switch the alarm (alarms) press and hold
the «ALARM 1» button (4) and/or the «ALARM
2» button (5) on in the current time mode until
(24) «AL 1» and/or (23) «AL 2» indicators,
respectively, appear on the display.
2.
To switch the alarm (alarms) off press and
hold the same button in the current time
mode again. Indicator of the corresponding
alarm will switch off.
Alarm snooze
1.
You can switch off the alarm signal for 9 min-
utes by pressing the “SNOOZE/SLEEP” but-
ton (6).
The indicator of the selected alarm
will flash, alarm signal will be repeated in 9
minutes.
2.
To switch off alarm sound signal press the
“ON/OFF” button (11) or button of corre-
sponding alarm (4) ALARM 1 or (5) ALARM 2.
Note: The alarm/radio signal will sound for 30
minutes if you do not press any buttons.
Display (2) brightness setup
Set up the necessary display brightness by
pressing the “DIMMER” button (6) repeatedly in
the current time mode.
Sequential displaying mode
You can switch on the time, year, current date and
temperature sequential displaying mode.
1.
To activate this mode press and hold the
«DISPLAY» button (10) until the symbol «on»
appears on the display.
2.
To switch off the sequential displaying mode
press and hold the «DISPLAY» button (10)
until the symbol «OFF» appears on the dis-
play.
Display (2) automatic switching off
1.
To activate the mode press and hold the
«NAP/M+» button (3) until the indicator (25)
«OFF» appears. The display will switch off in
10 seconds.
Note: This function is inactive in the radio mode.
1.
To switch off the function press and hold the
«NAP/M+» button (3) until the «OFF» indica-
tor (25) switches off.
Countdown timer
1.
Press the «NAP/M+» button (3) in the current
time mode, the symbol «n90» will appear on
the display, that means countdown timer
actuation in 90 minutes.
2.
Set the time of timer actuation from 10 to 90
minutes with 10 minutes step by pressing the
«NAP/M+»button (3) repeatedly.
3.
To view the remaining time press the «NAP/
M+» button (3).
4.
After the set time runs off you will hear a
sound signal, to switch it off press the but-
ton (11).
5.
To cancel this function press the «NAP/M+»
button (3) repeatedly until “OFF” symbol
appears on the display (2) or switch on the
radio pressing the button (11).
Temperature displaying
1.
To view the built-in thermometer readings
press the «TEMP» button (7) once in the
current time mode and twice - in the radio
mode.
2.
To select temperature measurement units
(Celsius degrees, Fahrenheit degrees) press
the «TEMP» button (7), then «DST/C-F» but-
ton (9).
Radio stations reception
1.
Connect the unit to the mains and press the
button (11).
2.
Use the buttons (8) and (9) for tuning to the
desired radio station.
Manual tuning:
consequently press the buttons
(8) and (9) to select the desired radio station with
step 0.1 MHz in Fm mode.
VT-3516 IM.indd 5
26.01.2012 12:48:27
