53

PI-005_v02

6

 Power adjustment buttons 

, 

7

 TIMER buttons 

, 

, 

8

 Lock button 

9

 ON/OFF button 

Preparing the appliance for operation

After switching on the appliance a single beep will be heard 

and all indicators will light for about 1 second – it means that 

the induction hob is in the standby mode.

Selection of utensils

The induction hob detects if the utensil placed on the heating 

zone is suitable for use with the appliance.

1

 Place the utensil on the heating zone.

2

 If the indicator shows the symbol “ ”, the utensil is not 

suitable for use with the induction hob. 

3

 If it is possible to operate the appliance after setting the 

power level, it means that the utensil may be used with the hob.

  Make sure that the bottom of the utensil is 

fl

 at 

and that its diameter must be at least equal to 

the diameter of the heating zone used.

You may use a magnet to check of the utensil is suitable for 

use with the induction hob. If the magnet “attaches” to the 

bottom of the utensil, it may be used for induction cooking.

Operating the hob

1

 Switch on the hob with the 

 button. All indicators will 

show “ ”. 
In case there is no operation within 1 minute since the 

moment of pressing ON/OFF button, the plate shall charge 

to stand-by mode.

2

 Place the utensil in the selected heating zone.

3

 Select the desired power level (1-9) using the 

, 

buttons. The default setting is 4.

If you simultaneously press the 

, 

 buttons for the 

given heating zone, the power setting will be reduced to 

0 and the heating zone will stop operating.
After removing the utensil from the heating zone, the 

heating zone stops operating and the symbol “ ” on the 

power level indicator  will 

fl

 ash for one minute. After that 

the heating zone switches off (symbol “ ”). 
If you place the utensil back on the heating zone 

when the symbol “ ” is 

fl

 ashing, the heating zone will 

automatically return to heating at the previous setting.

4

 After operation, switch off the hob with the 

 button.

  The maximum power of the complete plate is 3500 

W. Therefore the plate automatically reduces the 

output power, and the maximum admissible sum 

of all power levels of particular heating zones 

amounts 16. For instance 4/4/4/4 or 9/0/7/0.

Power and size of the individual heating zones

Heating 

zone

Size

Operation mode

Maximum power

I

∅ 

180 mm

Normal mode

2000 W

BOOSTER 

function

2800 W

II

∅ 

180 mm

Normal mode

1500 W

BOOSTER 

function

2000 W

III

∅ 

180 mm

Normal mode

2000 W

BOOSTER 

function

2800 W

IV

∅ 

140 mm

Normal mode

1500 W

BOOSTER 

function

2000 W

HEAT INDICATOR

When using the hob for a longer period of time, the given 

heating zone remains hot for some time after switching the 

appliance off. The symbol “ ” on the power indicator of the 

given heating zone warns against accidental touching of the 

hot hob. 

DETECTING IMPROPER ITEMS

If an item of an improper size (scissors, knife, fork, keys 

etc.) or a non-magnetic utensil is placed on the hob, it will 

automatically switch to the standby mode

OVERHEAT PROTECTION

The hob is equipped with a built-in sensor, which measures 

the temperature inside the hob. If the permitted temperature 

value is exceeded, the induction hob will automatically 

switch off.

AUTOMATIC SWITCH OFF

When the heating zone is switched on without any operation, 

the hob will switch off automatically upon the lapse of a default 

time depending on the set power level. See table below:

Power level

Time

1-3

8 hours

4-6

4 hours

7-9

2 hours

BOOSTER function

The BOOSTER function temporarily increases the power of 

the given heating zone.

  The BOOSTER function operates for a maximum 

of 5 minutes and afterwards the heating zone 

returns to the previous power setting.

  To switch on the BOOSTER function, the power 

indicator on given heating zone must 

fl

 ash.

1

 Press the 

 button.