10
eN
english
!
The appliance must be installed by a qualified person
in compliance with the instructions provided.
!
Wear gloves when carrying out installation and
maintenance operations.
aIr VeNT
(for ducting versions)
!
Prepare the hole and the air vent duct (150 mm dia-
meter).
!
Use a duct of the minimum indispensible length.
!
Use a duct with as few elbows as possible (maximum
elbow angle: 90°).
!
Avoid drastic changes in the duct cross-section.
!
Use a duct with an as smooth as possible inside.
!
The duct must be made of certified material.
!
Do not connect the hood to smoke exhaust ducts
for the products of combustion (boilers, fireplaces,
stoves, etc).
!
For the air vents comply with the provisions laid down
by the competent authorities.
In addition, the air must not be evacuated through a
hole in the wall unless specifically intended for this
purpose.
!
Fit air intakes in the room to prevent the hood from
creating a negative pressure in the room (which must
not exceed 0.04 mbar); if the hood is used at the
same time as non-electrical equipment (gas-, oil- and
charcoal-fired stoves, etc.) the exhaust gas may be
sucked in by the heat source.
FIlTerING or dUcTING VerSIoN ?
The hood may be in filtering or in ducting version. Deci-
de from the outset which type is to be installed.
For better efficiency, we recommend installing the hood
in the ducting version (if possible).
ducting version
The hood purifies the air and evacuates it to the outside
through an exhaust duct (diameter 150 mm).
Filtering version
The hood purifies the air and recycles the clean air
back into the room. For this version, the following are
required: 1 air baffle, 1 reducer, 1 charcoal filter.
The upper flue air evacuation slots must be positioned
at the top.
coNTrolS
P1:
Lights Off.
P2:
Lights On.
P3:
Motor Off / Speed -.
when held down, the
motor is turned off
storing the current
speed.
P4:
Blower On / Speed +.
P5:
5’ Timer Delay / Filter
Alarm Reset function.
l1:
The 4 green LEDs
indicate set speed.
l2:
1) When the motor
is off, it indicates
that the filter alarm is
active
oN red FIXed:
30-
hour filter alarm
oN red BlINKING:
120-hour filter alarm
2) When the motor is
on, it indicates that
the 5’ timer function is
active by
BlINKING
GreeN
.
5’ timer:
When the function is active, L2 blinks. The motor turns
off after 5’.
Filter alarm:
After 30h of motor operation, the LED L2 comes on red
fixed for 30’’ each time the motor is turned off.
After 120h of motor operation, the LED L2 comes on
red blinking for 30’’ each time the motor is turned off.
To reset this alarm, press P5 for 2’’ during blinking.
MaINTeNaNce
!
Before cleaning or maintenance cut the power.
cleaning the hood
WHEN TO CLEAN IT: clean it at least every 2 months
to prevent the risk of fire.
EXTERNAL CLEANING: use a cloth moistened in luke-
warm water and neutral detergent (for painted hoods);
use specific products for steel, copper or brass hoods.
INTERNAL CLEANING: use a cloth (or brush) soaked
in denatured ethyl alcohol.
WHAT NOT TO DO: do not use abrasive or corrosi-
ve products (e.g. metal sponges, brushes, too hard
brushes, very aggressive detergents, etc.)
P1
P2
P3
P4
L1
P5
L2
OFF
ON
OFF/-
OFF/+
R