! All parts which ensure the safe operation of the appliance must not be 

removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate 

with alternating current at the voltage and frequency indicated on the data 

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by 

inserting a screwdriver into the side 

tabs of the cover. Use the screwdriver 

as a lever by pushing it down to open 

the cover (see diagram).

2. Install the power supply cable by 

loosening the cable clamp screw 

and the three wire contact screws  
L-N-

.

Connect the wires to the 

corresponding terminals: the Blue 

wire to the terminal marked (N), the 

Brown wire to the terminal marked 

(L) and the Yellow/Green wire to the 
terminal marked 

 (see diagram).

3. Secure the cable by fastening the 

clamp screw.

4. Close the cover of the terminal 

board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data 

plate (see table). 

The appliance must be directly connected to the mains using an omnipolar 

switch with a minimum contact opening of 3 mm installed between the 

appliance and the mains.  The switch must be suitable for the charge indicated 

and must comply with current electrical regulations (the earthing wire must not 

be interrupted by the switch). The supply cable must be positioned so that it 

does not come into contact with temperatures higher than 50°C at any point 

(the back panel of the oven, for example).

!

 The installer must ensure that the correct electrical connection has been 

performed and that it is fully compliant with safety regulations.

N

L

Before connecting the appliance to the power supply, make sure that

•  The appliance is earthed and the plug is compliant with the law.

•  The socket can withstand the maximum power of the appliance, which is 

indicated on the data plate.

•  The voltage is in the range between the values indicated on the data plate.

•  The socket is compatible with the plug of the appliance. If the socket is 

incompatible with the plug, ask an authorised technician to replace it. Do 

not use extension cords or multiple sockets.

!

 Once the appliance has been installed, the power supply cable and the 

electrical socket must be easily accessible.

!

 The cable must not be bent or compressed.

!

 The cable must be checked regularly and replaced by authorised technicians 

only (see Assistance).

!

The manufacturer declines any liability should these safety measures 

not be observed.

Gas connection

The appliance should be connected to the main gas supply or to a gas 

cylinder in compliance with current National regulations. Before carrying 

out the connection, make sure the cooker is compatible with the gas supply 

you wish to use. If this is not the case, follow the instructions indicated in the 

paragraph “Adapting to different types of gas.”

When using liquid gas from a cylinder, install a pressure regulator that complies 

with current National regulations.

!

 Check that the pressure of the gas supply is consistent with the values 

indicated in Table 1 (“Burner and nozzle specifications”) since this will ensure 

the safe operation and longevity of your appliance while maintaining efficient 

energy consumption.

!

 Should you need to install a gas hob on top of a built-in gas oven, it is strictly 

forbidden to connect the two or to use a single cut-off tap. The two appliances 

should be connected separately, and each one should have its own stop tap in 

order to make them completely independent from one another (see figures).

NO

OK

Connection with a rigid pipe (copper or steel)

!

 Connection to the gas system must be carried out in such a way as not to 

place any strain of any kind on the appliance.

There is an adjustable 

L

-shaped pipe fitting on the appliance supply ramp 

and this is fitted with a seal in order to prevent leaks. The seal must always be 

replaced after rotating the pipe fitting (the seal is provided with the appliance). 

The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a threaded 

attachment

The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment. 

These pipes must be installed so that they are never longer than 2000 mm 

when fully extended. Once connection has been carried out, make sure that 

the flexible metal pipe does not touch any moving parts and is not compressed.

!

 Only use pipes and seals that comply with current National regulations.

GB

7