![background image](/i/janome/37882/janome-dc-3600/h/janome-dc-3600-051.png)
6
6
1
3
2
50
РАЗДЕЛ V. УХОД ЗА МАШИНОЙ
Чистка шпульного отсека и тканенаправителей
ВНИМАНИЕ:
• Отключите питание и вытащите вилку из розетки.
• Не разбирайте машину иначе, чем описано в этой
инструкции.
ПРЕДУПРЕЖДЕНИЕ:
• Не храните машину в помещениях с повышенной
влажностью, а также рядом с радиаторами или на
прямом солнечном свете.
ПРИМЕЧАНИЕ:
Протирайте корпус машины мягкой тканевой
салфеткой и нейтральным мылом.
После чистки машины проверьте, установлены ли игла
и прижимная лапка.
Отвертка
Установочный винт
Игольная пластина
Щеточка от пыли
Челночный механизм
Шпуледержатель
Тканенаправитель (рейка)
Сухая мягкая ткань
Нажмите кнопку подъема/опускания иглы и поднимите
иглу, затем отключите питание машины, вытащите вилку
из розетки.
Снимите пластину челночного отсека, отодвинув кнопку
вправо. Вытащите шпульку. Вычистите пыль и обрезки
ткани щеточкой.
Снимите установочный винт с левой стороны
игольной пластины при помощи отвертки ,
прилагаемой к машине. Снимите игольную пластину.
Поднимите шпуледержатель и вытащите его.
Прочистите шпуледержатель щеточкой и мягкой
тканью.
Прочистите тканенаправители и челночный механизм
мягкой щеточкой.
Протрите центр челночного механизма сухой мягкой
тканью.
* Можно воспользоваться пылесосом.
* Машина не требует смазки.
Сборка шпуледержателя
Шпуледержатель
Стопор
Головка
Направительные выступы игольной пластины
Отвертка
Отверстия
Вставьте шпуледержатель так, чтобы головка подошла
к стопору шпуледержателя.
Вставьте шпульку.
Установите игольную пластину с винтом.
После чистки вставьте иглу и прижимную лапку.
50
SECTION V. CARE OF YOUR MACHINE
Clean the Hook Race and Feed Dog
WARNING:
• Turn the power switch off and unplug the machine
before cleaning.
• Do not dismantle the machine other than as explained in
this section.
CAUTION:
• Do not store the machine in a high-humidity area, near
a heat radiator, or in direct sunlight.
NOTE:
Clean the outside of the machine with a soft cloth and
neutral soap.
After cleaning the machine, make sure the needle and
presser foot are attached.
q Screw driver
w Set screw
e Needle plate
r Lint brush
t Hook race
y Bobbin holder
u Feed dog
i Soft, dry cloth
Press the up/down needle position button to raise the
needle, then unplug the sewing machine.
Remove the cover plate by sliding the cover plate release
button to the right. Take out the bobbin. Brush out dust and
lint. (You may also use a vacuum cleaner.)
z Remove the set screw w on the left hand side of the
needle plate e with the screwdriver q supplied with the
machine. Remove the needle plate e.
x Lift up the bobbin holder y and remove it.
c Clean the bobbin holder y with a lint brush.
v Clean the feed dog and hook race with the lint brush.
b Clean the center of the hook race with a dry cloth.
* You may also use a vacuum cleaner.
* The machine does not require oiling.
Assemble the Hook Race
q Bobbin holder
w Stopper
e Knob
r Needle plate guide pins
t Screwdriver
y Guide holes
z Insert the bobbin holder so that the knob fits next to the
stopper in the hook race.
x Insert the bobbin.
c Attach the needle plate with screw.
After cleaning the machine, make sure the needle and
presser foot are attached.
q
w
e
y
r
y
r
u
t
i
r
w
e
q
t
y
z
x
c
v
b
z
x
c
50
SECTION V. CARE OF YOUR MACHINE
Clean the Hook Race and Feed Dog
WARNING:
• Turn the power switch off and unplug the machine
before cleaning.
• Do not dismantle the machine other than as explained in
this section.
CAUTION:
• Do not store the machine in a high-humidity area, near
a heat radiator, or in direct sunlight.
NOTE:
Clean the outside of the machine with a soft cloth and
neutral soap.
After cleaning the machine, make sure the needle and
presser foot are attached.
q Screw driver
w Set screw
e Needle plate
r Lint brush
t Hook race
y Bobbin holder
u Feed dog
i Soft, dry cloth
Press the up/down needle position button to raise the
needle, then unplug the sewing machine.
Remove the cover plate by sliding the cover plate release
button to the right. Take out the bobbin. Brush out dust and
lint. (You may also use a vacuum cleaner.)
z Remove the set screw w on the left hand side of the
needle plate e with the screwdriver q supplied with the
machine. Remove the needle plate e.
x Lift up the bobbin holder y and remove it.
c Clean the bobbin holder y with a lint brush.
v Clean the feed dog and hook race with the lint brush.
b Clean the center of the hook race with a dry cloth.
* You may also use a vacuum cleaner.
* The machine does not require oiling.
Assemble the Hook Race
q Bobbin holder
w Stopper
e Knob
r Needle plate guide pins
t Screwdriver
y Guide holes
z Insert the bobbin holder so that the knob fits next to the
stopper in the hook race.
x Insert the bobbin.
c Attach the needle plate with screw.
After cleaning the machine, make sure the needle and
presser foot are attached.
q
w
e
y
r
y
r
u
t
i
r
w
e
q
t
y
z
x
c
v
b
z
x
c
1
3
4
2
5
7
8
6
1
3
4
2
5
6
1
2
3
1
2
3
4
5