ENGLISH



Getting Started

Preparation

Basic Operation

Troubleshooting

Settings

Others

- To allow better heat dissipation, keep a clearance between 

this unit and its surrounding as shown below. When this 

unit is enclosed in a space of dimensions as shown below, 

use an air-conditioner so that the internal and external 

temperatures are the same.

-

the type of power supply to your home, consult your 

product dealer or local power company.

- This product is equipped with a three-wire plug. This plug 

will fit only into a grounded power outlet. If you are unable 

to insert the plug into the outlet, contact your electrician to 

install the proper outlet. Do not defeat the safety purpose 

of the grounded plug.

- Power-supply cords should be routed so that they are not 

likely to be walked on or pinched by items placed upon or 

against them. Pay particular attention to cords at doors, 

plugs, receptacles, and the point where they exit from the 

product.

- For added protection of this product during a lightning 

storm, or when it is left unattended and unused for long 

periods of time, unplug it from the wall outlet and 

disconnect the cable system. This will prevent damage to

the product due to lightning and power line surges.

- Do not overload wall outlets, extension cords, or 

convenience receptacles on other equipment as this can 

result in a risk of fire or electric shock.

- Never push objects of any kind into this product through 

openings as they may touch dangerous voltage points or 

short out parts that could result in a fire or electric shock. 

Never spill liquid of any kind on the product.

- Do not attempt to service this product yourself as opening 

or removing covers may expose you to dangerous 

voltages and other hazards. Refer all service to qualified 

service personnel.

- Unplug this product from the wall outlet and refer service to 

qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen on the product.

c) If the product has been exposed to rain or water.

d) If the product does not operate normally by following the 

operating instructions. Adjust only those controls that are 

covered by the Operation Manual, as an improper adjustment 

of controls may result in damage and will often require 

extensive work by a qualified technician to restore the product

to normal operation.

e) If the product has been dropped or damaged in any way.

f) When the product exhibits a distinct change in performance -

this indicates a need for service.

- When replacement parts are required, be sure the service 

technician has used replacement parts specified by the

manufacturer or with same characteristics as the original

part. Unauthorized substitutions may result in fire, electric 

shock, or other hazards.

- Upon completion of any service or repairs to this product, 

ask the service technician to perform safety checks to 

determine that the product is in proper operating condition.

- The product should be placed more than one foot away 

from heat sources such as radiators, heat registers, 

stoves, and other products (including amplifiers) that 

produce heat.

- When connecting other products such as VCR’s, and DVD 

players, you should turn off the power of this product for 

protection against electric shock.

- Do not place combustibles behind the cooling fan. For 

example, cloth, paper, matches, aerosol cans or gas 

lighters that present special hazards when over heated.

- Do not look into the projection lens while the illumination 

lamp is turned on. Exposure of your eyes to the strong 

light can result in impaired eyesight.

- Do not look into the inside of this unit through vents 

(ventilation holes), etc. Do not look at the illumination lamp 

directly by opening the cabinet while the illumination lamp 

is turned on. The illumination lamp also contains ultraviolet 

rays and the light is so powerful that your eyesight can be 

impaired.

- Do not drop, hit, or damage the light-source lamp (lamp 

unit) in any way. It may cause the light-source lamp to 

break and lead to injuries. Do not use a damaged light 

source lamp. If the light-source lamp is broken, ask your 

dealer to repair it. Fragments from a broken light-source

lamp may cause injuries.

- The light-source lamp used in this projector is a high 

pressure mercury lamp. Be careful when disposing of the 

light-source lamp. If anything is unclear, please consult 

your dealer.

- Do not ceiling-mount the projector to a place which tends 

to vibrate; otherwise, the attaching fixture of the projector 

could be broken by the vibration, possibly causing it to fall 

or overturn, which could lead to personal injury.

- Use only the accessory cord designed for this product to 

prevent shock.

*

DO NOT allow any unqualified person to install the 

unit.
Be sure to ask your dealer to install the unit (e.g. 

attaching it to the ceiling) since special technical 

knowledge and skills are required for installation. If 

installation is performed by an unqualified person, it 

may cause personal injury or electrical shock.

power source indicated on the label. If you are not sure of 

150 mm

and above

150 mm and above

300 mm 

and above

200 mm 

and above