14

15

C 18 ID

.........................1/4" (6,35 mm)

....................0-2200 min

-1

....................0-3200 min

-1

.........................158 Nm

........................M14 

...........................18 V

..........................1,6 kg

..........................1,8 kg

...........................78 dB (A)

...........................89 dB (A)

..........................2,8 m/s

2

..........................1,5 m/s

2

ENGLISH

BATTERIES

New battery packs reach full loading capacity after 4 - 5 

chargings and dischargings. Battery packs which have not 

been used for some time should be recharged before use.

Temperatures in excess of 50°C (122°F) reduce the 

performance of the battery pack. Avoid extended exposure 

to heat or sunshine (risk of overheating).

The contacts of chargers and battery packs must be kept 

clean.

For an optimum life-time, after use, the battery packs have 

to be fully charged. 

To obtain the longest possible battery life remove the battery 

pack from the charger once it is fully charged.

For battery pack storage longer than 30 days: 

Store the battery pack where the temperature is below 27°C 

and away from moisture 

Store the battery packs in a 30% - 50% charged condition 

Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit 

situations that cause high current draw, the tool will vibrate 

for about 2 seconds and then the tool will turn OFF.  

To reset, release the trigger. 

Under extreme circumstances, the internal temperatur of the 

battery could become to high. If this happens, the battery 

will shut down. 

Place the battery on the charger to charge and reset it.

INTENANCE

Use only Milwaukee accessories and spare parts. Should 

components need to be replaced which have not been 

described, please contact one of our Milwaukee service 

agents (see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. 

Please state the Article No. as well as the machine type 

printed on the label and order the drawing at your local 

service agents or directly at: Milwaukee Electric Tool, 

Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before 

starting the machine.

Remove the battery pack before starting any 

work on the machine.

Do not dispose of electric tools together with 

household waste material! In observance of 

European Directive 2002/96/EC on waste 

electrical and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their 

life must be collected separately and returned to 

an environmentally compatible recycling facility.

ENGLISH

TECHNICAL DATA 

Cordless Impact Screwdriver

Tool reception ..........................................................................

No-load speed .........................................................................

Impact range............................................................................

Torque......................................................................................

Max. diameter bolt / nut ...........................................................

Battery voltage.........................................................................

Weight according EPTA-Procedure 01/2003 (1,5 Ah) .............

Weight according EPTA-Procedure 01/2003 (3,0 Ah) .............

Noise/vibration information

Measured values determined according to EN 60 745.

Typically, the A-weighted noise levels of the tool are:

  Sound pressure level (K = 3 dB(A)) .......................................

  Sound power level (K = 3 dB(A)) ............................................

Wear ear protectors!
Total vibration values (vector sum in the three axes) 

determined according to EN 60745.

Vibration emission value a

h 

  Impact tightening of fasteners of the maximum capacity of the tool .

  Uncertainty K= ......................................................................

 WARNING! Read all safety warnings and all 

instructions, including those given in the accompanying 

brochure. Failure to follow the warnings and instructions 

may result in electric shock, fire and/or serious injury.  

Save all warnings and instructions for future reference. 

SAFETY INSTRUCTIONS

Wear ear protectors. Exposure to noise can cause hearing 

loss.

Hold power tool by insulated gripping surfaces, when 

performing an operation where the fastener may 

contact hidden wiring. Fasteners contacting a „live“ wire 

may make exposed metal parts of the power tool „live“ and 

could give the operator an electric shock.

Sawdust and splinters must not be removed while the 

machine is running.

When working in walls ceiling, or floor, take care to avoid 

electric cables and gas or waterpipes.

Remove the battery pack before starting any work on the 

machine.

Do not dispose of used battery packs in the household 

refuse or by burning them. Milwaukee Distributors offer to 

retrieve old batteries to protect our environment.

Do not store the battery pack together with metal objects 

(short circuit risk).

Use only System C 18 chargers for charging System C 18 

battery packs. Do not use battery packs from other systems.

Battery acid may leak from damaged batteries under 

extreme load or extreme temperatures. In case of contact 

with battery acid wash it off immediately with soap and 

water. In case of eye contact rinse thoroughly for at least 10 

minutes and immediately seek medical attention.

SPECIFIED CONDITIONS OF USE

The cordless impact wrench can be used to tighten and 

loosen nuts and bolts wherever no mains connection is 

available.

Do not use this product in any other way as stated for 

normal use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is 

in conformity with the following standards or standardized 

documents. 

EN 60745-1:2009 + A11:2010 

EN 60745-2-2:2010 

EN 55014-1:2006 + A1:2009 + A2:2011  

EN 55014-2:1997 + A1:2001 + A2:2008  

in accordance with the regulations 

2011/65/EU (RoHs)  

2006/42/EC 

2004/108/EC

Winnenden, 2012-09-11

Rainer Kumpf 

Director Product Development

Authorized to compile the technical file

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given 

in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different 

applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase 

the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or 

when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the 

accessories, keep the hands warm, organisation of work patterns.