![background image](/i/president/152872/president-lincoln-ii/h/president-lincoln-ii-033.png)
33
14) CH9/19 ~ LOCK
CH9/19
(short press)
Press
CH19/9
key (
14
) to
enter
Emergency Channel. LCD shows
“EMG”
. First
time to
select
channel
19,
second time for channel
9
, third time to
go back
to current channel.
LOCK
(long press)
Long press CH19/9-
LOCK
key (
14
) to
enable
key
LOCK
function. LCD shows
“ ”
.
Long press CH19/9-
LOCK
key (
14
) again to
disable
key
LOCK
function.
“ ”
disappears from LCD.
Note:
When active, front panel keys are locked except
PTT
pedal and rotaty
knobs (
PUSH
knob (
6
) is locked). LCD shows
“
Err
”
when locked key is pressed.
15) NB/ANL ~ HI-CUT
NB/ANL
(short press)
3 positions switch:
Off •
NB
(
NB
filter activated)
•
NB/ANL
(both
filters
activated).
When active, the filter is displayed on the LCD.
NB:
Noise Blanker /
ANL:
Automatic Noise Limiter. These filters allow reducing
back ground noises and some reception interferences.
HI-CUT
(long press)
HI-CUT:
Cuts out the high frequency interferences and has to be used
in accordance with the reception conditions. When active
“HI-CUT”
is
displayed on the LCD.
16) ROGER ~ BEEP
ROGER BEEP
(short press)
Press
ROGER
key (
16
) to
enable
/
disable
the
ROGER BEEP
function.
“ROGER”
appears on the LCD when the function is active.
The Roger Beep sounds when the
PTT
pedal (
23
) of the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a “simplex” communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
finished talking, he said “Roger” in order to prevent his correspondent that
it was his turn to talk. The word “Roger” has been replaced by a significant
beep. There comes “Roger beep” from.
KEY BEEP
(long press)
Press ROGER-
BEEP
key (
16
) for 2 seconds to
enable
/
disable
the
KEY BEEP
function.
A beep sounds when key is pressed, changing the channel etc.
“ ”
appears
on the display when the function is active.
17) SCAN ~ DW
SCAN
(short press)
Press
SCAN
key (
17
) to
enable
SCAN
function. LCD shows
“SCAN”
. The scan-
ning stops as soon as there is a busy channel. In
SCANNING
, press
s
/
t
to
change scan direction.
Press
SCAN
key (
17
) again or
PTT
pedal (
23
) to
exit
scan.
DUAL WATCH
(long press)
This function allows to
survey
between channel set on in the
[
]
menu
(see page 36)
and the current channel.
Long press SCAN-
DW
key (
17
) to
enable
DW
function. LCD shows
“DW”
.
Long press SCAN-
DW
key (
17
) again or
PTT
pedal (
23
) to
exit
DW
function.
18) MODE ~ CTCSS/DCS
MODE
(short press)
Press
MODE
key (
18
) to
select
the modulation mode: AM ~ FM ~ USB ~ LSB ~
CW or PA. Corresponding mode is displayed on the LCD.
Your modulation mode has to correspond to the one of your correspondent.
- Frequency Modulation /
FM
: for nearby communications on a flat open field.
- Amplitude Modulation /
AM
: communication on a field with relief and ob-
stacles at middle distance (the most used).
- Upper and Lower Side Band /
USB-LSB
: used for long distance communica-
tions (according to the propagation conditions).
-
CW
is used with morse key on the
CW KEY
jack on the back panel (
F
).
- An external loud speaker can be connected to your LINCOLN II by the
PA
jack plug situated on the back panel PA.SP (
D
). The message transmitted
into the microphone will be directed towards the external speaker and be
amplified.
See §
MIC GAIN
page 31 for adjustment of volume.
CTCSS/DCS
(long press)
This function is only enabled in FM modulation
Long press MODE
-
CTCSS/DCS
key (
18
) to
enable
CTCSS tone or DCS code.
“CTCSS”
or
“DCS”
blinks on the LCD.
English