37

PG-004_v01

Gas and electrical connections

THE MANUFACTURER DOES NOT BEAR ANY 

RESPONSIBILITY FOR POSSIBLE DAMAGED 

CAUSED BY NON- OBSERVANCE OF STANDARDS 

AND REGULATIONS IN FORCE AS WELL AS HOB 

CONNECTION EXECUTED BY NOT AUTHORISED 

PERSON.

REMARK: Connection of the hob both to electrical and 

gas 

fi

 tting can be executed by quali

fi

 ed  authorised 

installer only.

Before connecting the hob to the electrical and gas 

fi

 tting check the information on the nameplate and 

herewith manual.

Before installing make sure that the local distribution 

●

conditions (the type of gas, its pressure) and the 

appliance adjustment are compliant.
The conditions of gas adjustment of the appliance are 

●

indicated on the nameplate.
The appliance is not connected to the fumes conduits. 

●

It should be installed and connected according to 

the binding installation regulations. The appropriate 

requirements concerning ventilation should be taken into 

consideration.
The 

fl

 exible gas connection shall be assembled such 

●

way, that it is not in contact with the furniture parts in 

move (i.e. drawer) and it shall be not located in the are 

with not enough space.
The wiring supplying the power to the hob shall be 

●

secured with properly selected safety device.
Upon installing the hob, the installer is obliged to check 

●

the tightness of the gas 

fi

 tting.

REMARK: The installer is obliged to 

fi

 ll in the warranty 

card, which is the basis for the warranty and guaranty.

Replacing the nozzles for the other  
type of gas 

(Fig. B)

ATTENTION: The hob nozzles replacing can be 

executed only by an authorised quali

fi

 ed installer.

The gas hob is the nozzles are defaulted for 2E (G20) gas. 

The other kinds of gas are:

BURNER

GAS

PRESSURE

NOZZLE 

MARKING

THERMAL 

CAPACITY

WOK

2E (G20)

3B/P (G30)

20 mbar

37 mbar

1.36

0.86

3300 W

LARGE

2E (G20)

3B/P (G30)

20 mbar

37 mbar

1.18

0.72

2500 W

MEDIUM

2E (G20)

3B/P (G30)

20 mbar

37 mbar

0.92

0.58

1500 W

SMALL

2E (G20)

3B/P (G30)

20 mbar

37 mbar

0.75

0.49

1000 W

1

 Remove the cap and crown.

2

 Unscrew the nozzle using a special spanner.

3

 Replace the nozzle screwing the appropriate one 

according to the table.

After the nozzles exchange adjust the burners (see 

”FLAME ADJUSTMENT”.

Upon nozzles replacement glue an adequate label 

indicating the gas type near the end of shaft connecting 

the hob manifold.

Technical specifi cation

The technical parameters of the hob are indicated at the 

nameplate of the appliance.  
The hob is equipped with a shaft with threaded end of G1/2” 

diameter for connecting to gas supply 

fi

 tting. In case of 

connection to LPG cylinder (propane –butane) the ending 

of the 

fl

 exible hose 

∅

 8 x 1mm is screwed on the threaded 

shaft end.
The gas hob is the 1st class appliance equipped with 

a connecting cord with protecting stand. It requires 

connection to the socket equipped with an earth pin.
the appliance meets the requirements of the standards in 

force.
The appliance is in conformance with the requirements of the 

following directives:

Appliances burning gaseous fuels – 90/396/EEC, 

–

93/68/EEC.

Low Voltage Devices (LVD) – 2006/95/EC.

–

Electromagnetic compatibility (EMC) – 2004/108/EC.

–

The product has been labelled with CE mark on the 

nameplate.

The appliance outline  

(Fig. D)

1

 Large burner 

Ø 100 mm 

2.5 kW

2

 Medium burner 

Ø 75 mm 

1.5 kW

3

 Small burner 

Ø 55 mm 

1.0 kW

4

 WOK burner 

Ø 130 mm 

3.3 kW

5

 Burner control knobs with electric ignition candle

6

 Burner grate

7

 Burner cap

8

 Burner crown

9

 Burner body

10

 Ignition candle

11

 Anti-gas 

fl

 ow security device

Flame adjusting 

(Fig. C)

1

 Switch on the burner and set the minimum 

fl

 ame   .

2

 Remove the ring knob from the spindle.

3

 Adjust the 

fl

 ame turning the screw inside the spindle with 

an appropriate screwdriver.