![background image](/i/zelmer/155067/zelmer-zzs-7051xl/h/zelmer-zzs-7051xl-121.png)
121
ZS-007_v03
TURNING THE DEVICE ON
1
Pull out the upper and lower basket, insert the dishes and push the baskets back into
the dishwasher. It is advisable to insert the lower basket before the upper one (see also
Loading the dishwasher baskets).
2
Use the detergent (see also Salts, detergents and shiners).
3
Turn on the water valve to increase pressure.
4
Put the plug in. Make sure the water is running at maximum pressure.
5
Close the door and make sure they are sealed shut.
6
Press the ON/OFF button.
7
Push the button to select the appropriate program depending on amount of dirt.
8
Press Start/Pause button to begin the washing process.
ATTENTION! You should here a click after closing the door tight.
After the dishwasher has finished the program, the indicator will flash for 8 seconds and
you will hear a sound signal. However, if you have delayed the start, the indicator will flash
for 8 seconds but there will be no sound signal.
ATTENTION! If all indicators start to flash, this means the device is broken. Turn
off the dishwasher, turn off the water supply, and call our service.
If you forget to put some of the dishes in
You can put the dishes in any moment before opening the detergent container.
1
Open slightly the door to stop the dishwasher.
2
When the sprinkler goes off, you can open the door wide.
3
Put in the dishes you have forgotten about.
4
Close the door, the dishwasher will restart after 10 seconds.
WARNING! Opening the door is dangerous, as it may result in burns from hot
water and steam inside the dishwasher.
Washing cycle end
When a washing cycle ends, you will hear a sound signal for 8 seconds. Turn of the
dishwasher by pressing the ON/OFF button, turn off the water supply and open the door.
Wait a few minutes before you take the dishes out of the dishwasher – in this way you will
avoid breaking the dishes, which is easier when they are hot. The time will also facilitate
drying.
Turn off the dishwasher
●
For 8 seconds you will hear a sound signal – it means that the program has ended.
1. Turn off the dishwasher by pushing the ON/OFF button.
2. Turn off the water supply.
Carefully open the door
●
Hot dishes are susceptible to damages. Let them cool off for ca. 15 minutes before you
take them out of the dishwasher.
Open the door and leave them open for a few minutes before taking out the dishes.
This way they will not be that hot and will be drier.
Take the dishes out of the dishwasher
●
It is nothing out of ordinary that the dishwasher is wet inside.
Empty the lower basket than the upper one. In this way the water will not drop down
from the upper basket onto the dishes placed in the lower basket.
Maintenance and cleaning
FILTERING SYSTEM
The filter prevents any large chunks of food or other items from entering the pump.
Leftovers may block the filter, if so, they need to be removed.
The filter system consists of a coarse filter, a main filter and a micro-filter.
The main filter
1
Pieces of food or dirt held in the filter are ground
down by a special stream of water
from the lower sprinkler and washed down the
drain hole.
The coarse filter
2
Coarse filter catches larger objects, such as
bones or glass, which may block the drain hole.
In order to remove any of those objects, push
lightly the threads of the filter and lift it up.
The micro-filter
3
This filter keeps impurities and leftovers within
the sewage and prevents their sedimentation
on dishes during the washing cycle.
After each use, check whether the filters are unobstructed.
●
You can take the whole filtering system out by unscrewing the coarse filter. Remove
●
the leftovers and wash the filters with running water.
Step 1:
Turn the filter
counterclockwise and lift it.
Step 2:
Lift the main filter.
Step 3:
Lift the micro-filter.
ATTENTION! If you follow the steps from 1 to 3, you will dismount the filtering
system. If you follow the procedure from step 3 to 1, you will reinstall the filtering
system.
Filtering unit
In order to make the dishwasher work at its best with highest efficiency, the filtering unit
must be cleaned regularly. Filters effectively remove parts of food from the washing water,
making it possible for it to be used again during the cycle. The dishwasher works better
and more efficient when the filters are cleaned on a regular basis. It is necessary to remove
any leftovers after each cycle by rinsing the semicircular filter and container with running
water. In order to remove the filtering unit, pull the handle of the container. The filtering
system should be cleaned once a week.
Use a brush for cleaning the coarse filter and the micro-filter. Assemble the parts of the
filtering unit as shown on the figure above and reinstall the whole unit in the dishwasher by
putting it in the socket and forcing it down.
The dishwasher may not be used without the filters. By placing the filters incorrectly, you
decrease the efficiency of the dishwasher, as well as may damage the dishes and cutlery.
WARNING! Never use the dishwasher without filters.
WARNING! Incorrect placing of a filter may cause damage to the dishes and
cutlery, as well reduce the efficiency level of the dishwasher.
3
1
2