10

MAINTENANCE AND CLEANING

10

SWITCHING ON THE MACHINE AND SELECTING A PROGRAMME

MAINTENANCE AND CLEANING

SWITCHING THE MACHINE OFF

Note: After the buzzer sound which indicates the end of the program when the washing program comes to an end (end indicator light is on), you can leave the door of 
your machine ajar in order to hasten the drying.

Note: 
If the machine door opens during washing or the power is cut off , the machine will go on to the program in case the door is shut or the power is back.

Note: 
If energy is cut or machine door is opened during drying process, program is terminated. Your machine becomes ready for new program selection.

When end of program indicator turns on 
, switch your machine off  by using the 
Power On/Off  button.

Pull the plug out of the outlet. 
Turn off  the water tap.

•  CLEANING THE MACHINE IN REGULAR INTERVALS PROLONGS THE 

MACHINE’S SERVICE LIFE.

Oil and lime may accumulate in the machine’s washing section. In case of such 
accumulation;

• 

Fill the detergent compartment without loading any dishes into the 
machine, select a programme that runs at high temperature, and start the 
machine. In case of insuffi

  ciency, use special cleansing material available 

in the market. (Cleansing material produced special to machines by 
detergent producers.)

• 

CLEANING THE SEALS IN THE MACHINE DOOR

• 

To clean any accumulated residues in the door seals, wipe the seals 
regularly by using a dampened cloth.

• CLEANING 

THE 

MACHINE

Clean the fi lters and spray arms at least once a week.

Unplug your machine and turn off  its tap before starting the cleaning.

Do not use hard materials when cleaning your machine. Wipe with a fi ne cleaning 
material and a dampened cloth.

• FILTERS

Check if any food wastes have remained on the coarse and fi ne fi lters.

If any food wastes are left, remove the fi lters and clean them thoroughly under the 
water tap.

a. Micro Filter

b. Coarse Filter

c. Metal/Plastic Filter

To remove and clean the fi lter 
combination, turn it counter 
clockwise and take it out by lifting 
upwards. 1 Pull and remove the 
metal/plastic fi lter. 3 Then pull 
the coarse fi lter out of the micro 
fi lter.2 Rinse it with lots of water 
under the tap. 

Refi t the metal/plastic fi lter. Insert the coarse fi lter into the micro fi lter in a way that 
the marks will correspond to one another. Attach micro fi lter into the metal/plastic 
fi lter and turn to the direction of arrow and it is locked when the arrow on micro fi lter 
can be seen from across. 4

• 

Never use your dishwasher without any fi lter.

• Incorrect 

fi tting of the fi lter will reduce the washing eff ectiveness.

• Clean 

fi lters are very important in terms of the proper running of the 

machine.

• SPRAY 

ARMS

Check whether or not the holes for the upper 
and lower spray arms are clogged. If there is any 
clogging, remove the spray arms and clean them 
under water. 

You can remove the lower spray arm by pulling it 
upwards, while the upper spray arm nut can be 
removed by turning the nut to the left.

Be sure that the nut is perfectly tightened when 
refi tting the upper spray arm.

• HOSE 

FILTER

Water is prevented by the inlet hose fi lter so as to avoid any damage to your machine 
because of any contamination (sand, clay, rust etc.) that might be occasionally carried 
in through the mains water supply or the indoor plumbing, and to forestall such 
complaints as yellowing and formation of deposits after washing. Check the fi lter and 
the hose from time to time and clean them if necessary. To clean the fi lter, fi rst turn off  
your tap and then remove the hose. After removing the fi lter from the hose, clean it 
under the tap. Insert the cleaned fi lter back into its place inside the hose. Refi t the hose.