8
English
b)
Use
power
tools
only
with
speci
fi
cally
designated
battery
packs.
Use of any other battery packs may create a risk of
injury and
fi
re.
c)
When
battery
pack
is
not
in
use,
keep
it
away
from
other
metal
objects
like
paper
clips,
coins,
keys,
nails,
screws,
or
other
small
metal
objects
that
can
make
a
connection
from
one
terminal
to
another.
Shorting the battery terminals together may cause
burns or a
fi
re.
d)
Under
abusive
conditions,
liquid
may
be
ejected
from
the
battery;
avoid
contact.
If
contact
accidentally
occurs,
fl
ush
with
water.
If
liquid
contacts
eyes,
additionally
seek
medical
help.
Liquid ejected from the battery may cause irritation
or burns.
6)
Service
a)
Have
your
power
tool
serviced
by
a
quali
fi
ed
repair
person
using
only
identical
replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep
children
and
in
fi
rm
persons
away.
When
not
in
use,
tools
should
be
stored
out
of
reach
of
children
and
in
fi
rm
persons.
PRECAUTIONS
FOR
CORDLESS
DRIVER
DRILL
1. Always charge the battery at a temperature of 10 –
40°C. A temperature of less than 10°C will result in
over charging which is dangerous. The battery cannot
be charged at a temperature higher than 40°C.
The most suitable temperature for charging is that of
20 – 25°C.
2. When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the
battery.
6. Do not dispose of the battery in
fi
re.
If the battery is burnt, it may explode.
7. When drilling in wall,
fl
oor or ceiling, check for buried
electric power cord, etc.
8. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose of
the exhausted battery.
9. Using an exhausted battery will damage the charger.
10. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or in
fl
ammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
11. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
SPECIFICATIONS
POWER
TOOL
Model
DS14DVC
DS18DVC
No-load speed (Low/High)
0 – 450 / 0 – 1250 min
–1
0 – 450 / 0 – 1250 min
–1
Capacity
Drilling
Wood
(Thickness 18 mm)
30 mm
38 mm
Metal
(Thickness 1.6 mm)
Steel: 12 mm
Steel: 13 mm
Driving
Machine screw
6 mm
6 mm
Wood screw
6.2 mm (diameter) × 63 mm (length)
(Requires a pilot hole)
8 mm (diameter) × 75 mm (length)
(Requires a pilot hole)
Rechargeable battery
BCC1412: Ni-Cd 14.4 V (1.2 Ah 12 cells)
BCC1812: Ni-Cd 18 V (1.2 Ah 15 cells)
Weight
1.7 kg
1.9 kg
CHARGER
Model
UC18YK
Charging voltage
7.2 – 18 V
Weight
0.35 kg
STANDARD
ACCESSORIES
In addition to the main unit (1), the package contains the
accessories listed in the table below.
DS14DVC
DS18DVC
1
Plus driver bit (No. 2 × 65L) ..................1
2
Charger (UC18YK) ................................1
3
Battery ..................................................2
or
Battery ..................................................3
(3SSK)
4
Plastic case ..........................................1
Standard accessories are subject to change without
notice.