![background image](/i/hotpoint-ariston/154642/hotpoint-ariston-7ofk1039elspx/h/hotpoint-ariston-7ofk1039elspx-017.png)
GB
17
!
Do not touch the light bulb directly with your hands.
!
Do not use the oven lamp as/for ambient lighting.
Sliding rack kit assembly
To assemble the sliding
racks:
1. Remove the two frames,
lifting them away from the
spacers A (see figure).
2. Choose which shelf to use
with the sliding rack. Paying
attention to the direction in
which the sliding rack is to
be extracted, position joint B
and then joint C on the
frame.
3. Secure the two frames
with the guide rails using the
holes provided on the oven
walls (see diagram). The
holes for the left frame are
situated at the top, while the
holes for the right frame are
at the bottom.
4. Finally, fit the frames on
the spacers A.
!
Do not place the sliding racks in position 5.
Automatic cleaning with the FAST CLEAN
function
With the FAST CLEAN mode, the internal temperature of the
oven reaches 500°C. The pyrolytic cycle is activated, burning
away food and grime residues. Dirt is literally incinerated.
Keep children away from the appliance during the automatic
cleaning cycle as surfaces may become very hot. Particles
may ignite inside the oven as a result of the combustion
process. There is no cause for concern: this process is both
normal and hazard-free.
Before initiating the FAST CLEAN mode:
• clean the oven door;
• remove large or coarse food residues from the inside of
the oven using a damp sponge. Do not use detergents;
• remove all accessories and the sliding rack kit (where
present);
• do not place tea towels or pot holders over the oven
handle.
A
B
C
Left
guide rail
Right guide
rail
Direction
of extraction
D
!
If the oven is too hot, the pyrolytic cycle may not start.
Wait for the oven to cool down.
!
The programme may only be started once the oven door
has been closed.
To activate the Fast Clean programme:
1. Switch the control panel on by pressing the
button.
2. Press the
button; the TIME display will show the default
duration of 1:30 h (normal cycle), while he TEMPERATURE
display will show “Piro” and “nor” alternately;
3. The desired cleaning level can be selected by pressing
the
button, then:
- pressing “ ” to switch to the intensive cycle: the duration
is 2 h and the TEMPERATURE display shows the text “Piro”
and “int” alternately;
- pressing “ ” to switch to the economy cycle: the duration
is 1 h and the TEMPERATURE display shows the text “Piro”
and “eco” alternately.
Safety devices
• the door locks automatically as soon as the temperature
reaches a high value; the
icon lights up on the
display;
• pressing the
button cancels the cleaning cycle t any
time;
• if a malfunction occurs, the heating elements will be
switched off;
• once the oven door has been locked, you cannot change
the duration and end time settings.
Programming delayed automatic cleaning
!
Programming is possible only after selecting the FAST
CLEAN mode.
1. Press the
button and set the end time using the “
” and “ ” buttons.
2. Once you have reached the desired end time, press the
button again.
3. Press the
button to activate the programmed mode.
4. When the selected time has elapsed, “END” appears on
the TEMPERATURE display and a buzzer sounds.
• For example: it is 9:00 a.m. and the Economy (ECO)
FAST CLEAN level has been selected, with the default
duration of 1 hour. 12:30 is scheduled as the end time.
The programme will start automatically at 11:30 a.m.
The icons
and
flash to indicate that programming
has taken place. After programming, in the time before the
Fast Clean mode starts, the TIME display indicates the
duration and end of the Fast Clean mode alternately.
To cancel programming press the
button.