GB

9

Start-up and use

WARNING!

The oven is 

provided with a stop system 

to extract the racks and 

prevent them from coming 

out of the oven (1).

As shown in the drawing, 

to extract them completely, 

simply lift the racks, holding 

them on the front part, and 

pull (2).

!

 The first time you use your appliance, heat the empty oven with 

its door closed at its maximum temperature for at least half an 

hour. Make sure that the room is well ventilated before switching 

the oven off and opening the oven door. The appliance may emit 

a slightly unpleasant odour caused by protective substances 

used during the manufacturing process burning away.

!

 To make the setting process easier, press and hold the “ ” 

and “ ” buttons to scroll through the numbers on the display 

rapidly.

!

 Each setting will automatically be stored in the appliance 

memory after 10 seconds.

!

 The touch controls cannot be activated if the user is 

wearing gloves.

!

 In order to optimise the cooking performance, when 

starting the selected function, product settings will be 

applied that could cause a delayed start of the fan and 

heating elements

Some models are equipped with a system of hinges which 

allows the door to close slowly, without the user having to 

follow the movement through with his/her hand. To use the 

system correctly, before closing the door:

•  Open the door fully.

•  Do not force the closing movement manually.

Control panel lock

!

 The control panel can be locked while the oven is off, once 

cooking has started or finished and during programming.

To lock the oven controls, press and hold the 

 button 

for at least 2 seconds. A buzzer will sound and the 

TEMPERATURE display shows the key symbol “O—n”. The 

 icon will light up to indicate lock activation.

To deactivate the lock, press and hold the 

 button again 

for at least 2 seconds.

!

 When cleaning the appliance, the door lock may be closed 

accidentally (there is an exposed spring). If this happens, 

reopen it by turning the door lock upwards (see figure).

KO

OK

Setting the clock

!

 The clock can only be set when the oven is switched off. If 

the oven is in standby mode, pressing the 

 button once will 

display the current time setting. Press it again to set the time.
After connection to the power supply network or after a 
blackout, the 

 button and the digits on the TIME display 

will flash for 10 seconds.

To set the clock:
1. Press the 

 button.

2. Adjust the hour figure using the “

” and “ ” buttons.

3. Once you have reached the correct hour value, press 

the 

 button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock. 
If the 

 icon flashes on the display, this indicates that the 

clock has not been set correctly.

Setting the minute minder

!

 The minute minder may be set regardless of whether the 

oven is switched on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer 

that will automatically stop after 30 seconds or when any 

active button on the control panel is pressed.

To adjust the timer proceed as follows:

1. Press button 

.

2. Set the desired time using buttons “ ” and “ ”.

3. Once you have reached the desired value, press the 

button again.
The lit 

 symbol will remind you that the minute minder 

is on.
To cancel the minute minder, press the 

 button and 

use the “ ” and “ ” buttons to set the time to 00:00. Press 
button 

 again.

The 

 icon will switch off to indicate that the minute minder 

has been disabled.

Starting the oven

1. Switch the control panel on by pressing the 

 button. 

The appliance buzzer sounds three times (ascending) and 

all buttons light up in sequence.

2. Press the button corresponding to the desired cooking 

mode. The TEMPERATURE display shows:

- the temperature associated with the mode, if programming 

manually;

- “Auto”, if programming is automatic.