I n s t a l l a t i o n   o f   g a s   c o o k e r s

«^Before your appliance is 
connected to the gas supply, 
check the ensure that the gas 
category and pressure 
specifications shown in the data 

plate corresponds with your gas 
supply. If necessary call 

authorized service 

for 

adjusting to gas category.

•‘This appliance shall be installed 

in 

accordance 

with 

the 

regulations in force and only used 
in  a  well  ventilated  space.  Read 

the  instructions  before  installing 
or 

using 

this 

appliances. 

In  the  interest  of  safety  this 
appliances  must  be  installed 
and/or  serviced  by  a  competent 
person as stated in the gas safety 
regulations current editions.

Please  refer  to  the  data  plate 

for  details  about  gas  supply  and 

pressures.

The  appliance  must  not  be 

installed  in  a  room  without  a 

window  or  other  controllable 
opening. If is installed in a room 
without  a  door  which  opens 

directly  to  tohe  outside,  a 
permanent  opening  is  required. 

The  air  circulation  should  be  2 

m3/h per kW of burners.

Connection of the gas hose to the oven

Convenient position is selected by interchanging 
the  hose  nozzle  and  plug  according  to  the 
location of the main gas inlet valve. If you make 
a  connection  with  a  flexible  metal  hose,  locate 
a  seal  between  the  main  gas  pipe.  The  inner 
diameter of the flexible hose, which the butane 
hose  nozzle  is  connected,  should  be  6mm  for 
the house-type gas tubes.

The  inner  diameter  of  the  flexible  hose,  which 
the  natural  hose  nozzle  is  connected,  should 

be  15mm.  The  hose  should  tightly  be  fitted  to 

the hose nozzle by squeezing with a clamp.The 

plastic hose end is soaked in hot water for 
one  minute  to  soften  and  inserted  fully 
into the hose nozzle. The clamp is fastened 
securely by a screw driver. The other end 
of the hose is connected to the gas valve 

with the same operation.

The  hose  should  be  replaced  before  its  last 
expiry date.

plug

Hose nozzle

¥

Caution!

Make the oven connection to the 

gas inlet valve, the hose length 
must be short and be sure that 
there is no leakage. The hose used 
should not be longer than 125 cm 
for safety.

Connection of the gas hose to 

the oven

Convenient  position  is  selected  by 
interchanging  the  hose  nozzle  and 
plug  according  to  the  location  of 

the  main  gas  inlet  valve. The plastic 

hose end is  soaked in hot water for 

one  minute  to  soften  and  inserted 
fully into the hose nozzle. The clamp 

is  fastened  securely  by  a  screw 
driver.  The  other  end  of  the  hose 
is  connected  to  the  gas  valve  with 

the same operation.

Gas leakage control
During control, be sure that the 
control knobs are closed and the gas 
inlet valve is open. Apply soap bubbles 

to the connections for leakage 
control. In case leakage exists, buble 
will appear. In such case, check the 

gas connection immediately. Do not 
control gas leaks by using fire. 

Caution!
Never use lighter or match 

flame, for controlling the gas 

k£kage.

Hose nozzle and elbow types 

for Natural gas and 

Butane/propane