![background image](/i/dell/157685/dell-5330dn/h/dell-5330dn-110.png)
a. The printer supports a wide range of media sizes.
b. Capacity may vary depending on print materials weight and thickness, as well as environmental conditions.
Guidelines for Using Paper
For best results, use conventional 75 g/m
2
(20 lb) paper. Ensure the paper is of good quality, free of cuts, nicks, tears, spots, loose particles, dust, wrinkles,
voids, and curled or bent edges.
If you are unsure of what type of paper you are loading, such as bond or recycled paper,
check the label on the package.
The following problems may cause print quality deviations, jamming, or even damage to the printer:
Paper Specifications
Folio
8.5 X 13 in.
(216 X 330 mm)
Minimum size (Custom)
3 x 5 in.
(76 x 127 mm)
60-210 g/m
2
bond (16-56 lb)
5 sheet of paper for the
multi-purpose feeder
Maximum size (Legal)
8.5 x 14 in.
(216 x 356 mm)
Transparency
Same minimum and
maximum paper sizes as
listed above.
138-146 g/m
2
(37-39 lb)
50 sheet of 75 g/m
2
bond
(20 lb) paper for the
multi-purpose feeder
Labels
120-176 g/m
2
(32-47 lb)
25 sheet of 75 g/m
2
bond
(20 lb) paper for the
multi-purpose feeder
Cards
60-210 g/m
2
(16-56 lb)
10 sheet of 75 g/m
2
bond
(20 lb) paper for the
multi-purpose feeder
Envelopes
75-105 g/m
2
(20-28 lb)
10 sheet of 75 g/m
2
bond
(20 lb) paper for the
multi-purpose feeder
NOTE:
You may experience jams when using print materials with a length of less than 127 mm (5 in). For optimum performance, ensure that you store
and handle the paper correctly. Please refer to
"Printer and Paper Storage Environment"
NOTE:
You can use A4, Letter, Folio, Oficio, Legal-sized paper for duplex printing.
Symptom
Problem with paper
Solution
Poor print quality or toner
adhesion, problems with feeding
Too moist, too rough, too smooth or
embossed; faulty paper lot
Try another kind of paper,
between 100-400 Sheffield, 4%-
5% moisture content.
Dropout, jamming, curl
Stored improperly
Store paper flat in its moisture-
proof wrapping.
Increased gray background
shading/printer wear
Too heavy
Use lighter paper, use the
rear
door
.
Excessive curl problems with
feeding
Too moist, wrong grain direction or
short-grain construction
l
Use the
rear door
.
l
Use long-grain paper.
Jamming, damage to printer
Cutouts or perforations
Do not use paper with cutouts or
perforations.
Problems with feeding
Ragged edges
Use good quality paper.
NOTE:
Do not use letterhead paper printed with low-temperature inks, such as those used in some types of thermography.
NOTE:
Do not use raised or embossed letterhead.
NOTE:
The printer uses heat and pressure to fuse toner to the paper. Ensure that any colored paper or preprinted forms use inks that are compatible
with this fusing temperature (180° C or 356°
F for 0.1 second).
Category
Specifications
Acid Content
5.5 pH or lower
Caliper
0.094-0.18 mm (3.0-7.0 mils)
Curl in Ream
Flat within 0.02 in (5 mm)
Cut Edge Conditions Cut with sharp blades with no visible fray.
Fusing Compatibility
Must not scorch, melt, offset, or release hazardous emissions when heated up to 180°
C (356°
F) for 0.1 second.
Grain
Long Grain
Moisture Content
4%-6% by weight