20

21

500 S 

545 S

.......................1300 W .........................1300 W

.........................650 W ...........................650 W

...............................  ..............................450 min

-1

...............................  ..............................450 min

-1

.......................2840 min

-1

 .....................2840 min

-1

.........................14/- J ..........................14/12 J

...............................  ................................45 mm

...............................  ................................65 mm

...............................  ..............................100 mm

...........................66 mm ..........................66 mm

..........................6,3 kg ............................6,7 kg

...............................  ................................96 dB (A)

...............................  ..............................107 dB (A)

...........................91 dB (A)

.........................101 dB (A)

.........................104 dB (A)

...............................  ................................13 m/s

2

...............................  ...............................1,5 m/s

2

........................ 11,5 m/s

2

 ...........................9 m/s

2

..........................1,9 m/s

2

 ........................1,9 m/s

2

ENGLISH

ENGLISH

TECHNICAL DATA

Rated input ..............................................................................

Output ......................................................................................

No-load speed .........................................................................

Speed under load max. ...........................................................

Rate of percussion under load max. ........................................

Single impact strength Drilling/Chiselling ................................

Drilling capacity in concrete .....................................................

Tunnel bit in concrete, bricks and limestone ...........................

Core cutter in concrete, bricks and limestone .........................

Chuck neck diameter ...............................................................

Weight without cable ...............................................................

Noise Information 545 S

Measured values determined according to EN 60 745.

Typically, the A-weighted noise levels of the tool are:

  Sound pressure level (K = 3 dB(A)) .......................................

  Sound power level (K = 3 dB(A)) ............................................

Wear ear protectors!
Noise Information 500 S

Typically the A-weighted sound pressure level of the  

tool is .......................................................................................

Measured values determined according to 2000/14/EG at the 

user’s ear.

2000/14/EC: Conformity assessment procedure according to 

Annex VI. Notified Body:  

VDE Testing and Certification Institute, Merianstr. 28,  

63069 Offenbach, Germany

  Measured sound power level ................................................

  Guaranteed sound power level .............................................

Wear ear protectors!
Vibration Information 

Total vibration values (vector sum in the three axes) 

determined according to EN 60745.

Vibration emission value a

h

:

Hammer-drilling in concrete: vibration emission value a

h 

 .......

Uncertainty K =  .......................................................................

Chiselling: vibration emission value a

h 

 ....................................

Uncertainty K =  .......................................................................

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the 

attached leaflet!

Wear ear protectors.

 Exposure to noise can cause hearing 

loss.

Use auxiliary handles supplied with the tool. 

Loss of 

control can cause personal injury.

Hold power tool by insulated gripping surfaces, when 

performing an operation where the cutting accessory 

may contact hidden wiring or its own cord. 

Cutting 

accessory contacting a „live“ wire may make exposed metal 

parts of the power tool „live“ and shock the operator.
Appliances used at many different locations including open 

air must be connected via a residual current device (FI, 

RCD, PRCD).
Always wear goggles when using the machine. It is 

recommended to wear gloves, sturdy non slipping shoes 

and apron. 
Sawdust and splinters must not be removed while the 

machine is running.

Always disconnect the plug from the socket before carrying 

out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. 

Always lead the cable away behind you.
When working in walls ceiling, or floor, take care to avoid 

electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to 

health. Do not inhale the dust. Wear a suitable dust 

protection mask.

SPECIFIED CONDITIONS OF USE

545 S: 

The pneumatic hammer can be universally used for 

hammer drilling and chiselling in stone and concrete.

500 S: 

The hammer can be used for chiselling in stone and 

concrete.
Do not use this product in any other way as stated for 

normal use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is 

in conformity with the following standards or standardized 

documents: EN 60745, EN 55014-1, EN 55014-2, 

EN 61000-3-2, EN 61000-3-3, in accordance with the 

regulations 98/37/EC, 89/336/EEC, 2000/14/EC (500 S)

Volker Siegle

Manager Product Development

Winnenden, 2007-01-24

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the 

system voltage indicated on the rating plate. It is also 

possible to connect to sockets without an earthing contact 

as the design conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all 

times.
Important note! If the carbon brushes are worn, in addition 

to exchanging the brushes the tool should be sent to after-

sales service. This will ensure long service life and top 

performance.
Use only Milwaukee accessories and Milwaukee spare 

parts. Should components need to be replaced which have 

not been described, please contact one of our Milwaukee 

service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. 

Please state the Article No. as well as the machine type 

printed on the label and order the drawing at your local 

service agents or directly at: Milwaukee Electric Tool, 

Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before 

starting the machine.

Always disconnect the plug from the socket 

before carrying out any work on the 

machine.

Accessory - Not included in standard 

equipment, available as an accessory.

Do not dispose of electric tools together 

with household waste material! In 

observance of European Directive 2002/96/

EC on waste electrical and electronic 

equipment and its implementation in 

accordance with national law, electric tools 

that have reached the end of their life must 

be collected separately and returned to an 

environmentally compatible recycling 

facility.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardized test given 

in EN 60745 and may be used to compare one tool with another.
The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the 

level given in this information sheet. This could lead to a significant underestimate of exposure when the tool is used regularly 

in such a way. 

Note:

 To be accurate, an estimation of the level of ex-posure to vibration experienced during a given period of work should 

also take into account the times when the tool is switched off and when it is running but not actually doing the job. This may 

significantly reduce the exposure level over the total working period.