![background image](/i/zelmer/158781/zelmer-zzs-9012xe/h/zelmer-zzs-9012xe-117.png)
117
ZS-003_v03
1
In order to open the dispenser, turn
the lid according to the arrow point at
OPENED sign (left) and remove it.
2
Add the shiner into the dispenser –
be careful not to pour too much.
3
Put on the lid back making sure the
arrow on OPENED sign, and turn it to the
right (to CLOSED sign).
A shiner is released during the last rinsing
in order to prevent any water drops from
staining the dishes. It also facilitates the
process of drying, making the water flow
down from the surfaces. The dishwasher
is designed for liquid shiners. The shiner dispenser is placed inside the door, next to the
detergent dispenser. In order to fill in the dispenser, unscrew the lid and pour the washing
liquid (shiner) into the dispenser until the level indicator turns completely black. The
capacity of the shiner dispenser is ca. 110 ml.
Be careful not to overfill the dispenser, as it may lead to excessive wear and tear of the
device. Use a wet cloth to wipe any spills. Do not forget to put the cap back on before you
close the door of the dishwasher.
ATTENTION! Clean the spills from the liquid with an absorbing cloth in order to
prevent foaming during the next washing process.
Shiner dispenser adjustment
Shiner dispenser has four to six settings. Start always from setting “4”. If there are any
stains or problems with drying increase the amount of shiner by lifting the lid of the
dispenser and turn the dial to “5”. If the dishes are still
stained and take a long time to dry set the dial to a higher
level till the problems seize. The recommended setting is
“4” (default setting – “4”).
ATTENTION! Increase the amount, if after the
process you can see water drop stains or limestone.
Decrease it, if you notice any white, sticky stains or
a blue residue on glass or knife blades.
When the amount of shiner changes, the size of the black dot situated on the indicator also
alters, as shown below.
full
3/4
1/2
1/4
empty
D
DETERGENTS
DETERGENT DISPENSER
The dispenser should be filled before each cycle according to the information provided in
the table of cycles.
Our dishwasher uses less detergents and shiners than an average dishwasher. Usually to
clean a full load of dishes, you need a tablespoon of detergents. The more dirty the dishes,
the more detergent you need. Add the detergent before starting the dishwasher, otherwise
it may dampen and does not dissolve fully.
Amount of detergent
Shiner level indicator
Shiner dispenser
1
2
3
Adjustment dial (shining)
1
Open the detergent container by pushing the lock (Fig.
1
)
.
2
Fill the container with the detergent (Fig.
2
).
3
The scale inside the container will help you to determine the right amount of the
detergent.
4
The detergent container holds 25 g of a detergent.
ATTENTION! If the lid is closed, press it to unlock and open it.
ATTENTION! Always add the detergent before each washing cycle.
ATTENTION! Use only premium dishwasher detergents.
WARNING! Dishwasher detergents cause corrosion! Keep them away from
children.
Correct use of detergents
Use only the detergents designer for dishwashers. Make sure it is fresh and dry. Do not
add the powder detergent to the container, until you want to start dishwashing.
Adding detergent to the container
Fill the container with the detergent.
The dosage markings are shown on the diagram to the right:
A
Place for the detergent used in the main washing cycle.
B
Place for the detergent used in preliminary washing and 3-in-1 tablets cycle, as well
as other compact detergents.
The minimum amount is marked on the dispenser as MIN.
1
2
Push the lock in order to open it