-
9
1 Belt suction turbine Sweeper
2 Belt of roller brush drive
Check both the belts for wear and prop-
er fitting.
Park the machine on an even surface.
Set main switch to “0”.
Secure the machine with wheel
chock(s) to prevent it from rolling away.
Remove waste containers on both
sides.
Front sealing strip
Loosen fastening nuts.
Align the sealing strip so that the bottom
edge trails behind at a distance of 35 to
40 mm.
Tighten nuts.
Rear sealing strip
The floor clearance of the rear sealing strip
is designed in such a way that the sealing
strip trails behind at a distance of 5 to 10
mm.
Replace sealing strip if worn out.
Dismantling the roller brush (see "Re-
placing the roller brush").
Loosen fastening nuts.
Screw on the new sealing strip.
Tighten nuts.
Side sealing strips
Loosen fastening nuts.
Set floor clerance by pushing in a sheet
of 1-2 mm thickness.
Adjust sealing strip.
Tighten nuts.
Install roller brush.
1 Lid of dust filter casing
2 Screws
3 Flange
4 Dust filter bearing
5 Dust filter
Loosen the lock of the hood of the
sweeper by turning it in.
Tilt up the sweeper hood.
Remove the lid of the dust filter casing.
Loosen both screws.
Turn the flange in an anticlockwise di-
rection and remove the dust filter bear-
ing.
Take out the dust filter.
Insert the new dust filter in such a way
that the holes point to the front of the
carrier.
Replace the dust filter bearing, turn in
clock-wise direction and fasten it with
screws.
Replace the lid and press it.
Close the sweeper hood.
Ensure proper locking of the hood by
turning.
Loosen 3 screws.
Remove the wiper blade.
Push in the new side brush.
Tighten 3 screws.
1 Screw
2 Tin cover
Pull out the waste container.
Loosen screws.
Tilt the tin cover upwards and remove it.
1 Bowden cable
2 Screw of the link bracket
3 Link
4 Cover
5 Lid screws
Hang out the Bowden cable.
Loosen and remove screws of the link
bracket.
Remove the crank.
Loosen and remove both screws of the
lid and open the cover.
Pull out roller brush.
Insert new roller brush and reassemble
the sweeper in the reverse sequence.
Readjust the Bowden cable.
In case of danger of frost:
Empty the fresh and dirt water reser-
voirs.
Store the appliance in a frost-protected
room.
Check sealing strips of sweeper
Replacing the dust filter
Replacing the side brushes
Replacing the roller brush
Frost protection
24
EN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
Инструкции и руководства похожие на KARCHER BD 100/250 R I BP
Другие инструкции и руководства из категории Поломоечная машина
