28
29
English
RSX-1560 Surround Sound Receiver
28
29
English
RSX-1560 Surround Sound Receiver
Front Panel:
Rotate the front-panel VOLUME knob clockwise to increase
the volume, counterclockwise to decrease.
Remote:
Press the VOL UP button to increase the volume; press the VOL
DOWN button to decrease.
When you adjust the volume, the setting is shown on the SDTV monitor
and/or the front-panel display. The current volume setting is also shown
on the SYSTEM STATUS OSD screen.
Note:
The VOLUME controls can be used to change the volume
in Zone 2, 3 or 4. Press the front-panel or remote control ZONE
button and adjust the volume. After 10 seconds, the VOLUME
control reverts to normal operation.
Muting the Sound
e
R
The volume of the receiver can be turned off or muted. Push the MUTE
button on the front panel or the remote once to turn the sound off. A
MUTE indication appears in the OSD and the front-panel displays. Press
the MUTE button again or adjust the volume settings to restore output
levels.
Selecting Inputs
Input Buttons
4w
A
You can select any of nine source inputs for listening and/or watching:
CD, TUNER, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, VIDEO 5, or
MULTI INPUT (EXT on remote).
The front-panel display and the ON-SCREEN DISPLAY show the name of
the current listening source selection. The labels for VIDEO sources can
be customized to match your components.
Note:
When the TUNER input source button is pressed, the
frequency of the currently tuned station is displayed. Pressing the
button again toggles the display to show the word TUNER instead
of the frequency display.
All of the source inputs can be customized using the ON-SCREEN
DISPLAY configuration menus to accept either analog signals or digital
signals from one of the seven assignable digital inputs, or HDMI Audio.
When a digital input is assigned, the unit checks for the presence of
a digital signal at that input. If a digital signal is present when the
source is selected, it is automatically activated and the proper surround
mode enabled. If no digital signal is present, the analog inputs for that
source are selected. This auto-sensing is the preferred configuration for
digital source inputs such as DVD players. When an ANALOG input is
assigned, the unit will not access a digital signal, even though one may
be available at the digital input.
By default, the source input buttons are factory configured to select the
following inputs:
CD:
Digital Coaxial 2
Tuner:
Analog (built-in)
Tape:
Digital Coaxial 3
Video 1:
HDMI Audio (HDMI 1)
Video 2:
HDMI Audio (HDMI 2)
Video 3:
Digital Optical 1
Video 4:
Digital Optical 2
Video 5:
Digital Coaxial 1
Each source input should be configured using the ON-SCREEN DISPLAY
menu system to use the desired input type (analog or digital auto-
sensing). See the INPUT MENU section for configuration instructions.
Note:
In addition to selecting analog or digital signals, the
configuration options also permit custom labeling and selection of
a default surround mode for each of the eight inputs.
The input source buttons can also be used with the SEL button (described
in the next section) to select an analog input source signal to be available
at the outputs for recording, or for any of the remote zones.
Selecting a Source Input from the Front Panel
4wrt
To select a source for LISTENING:
Press one of the eight INPUT
buttons or the MULTI INPUT button.
To select a source for RECORDING:
Press the SEL button once
(“RECORD” appears in the display) and then press one of the eight
INPUT buttons within 5 seconds.
To select a source for Zone 2, 3 or 4:
Press the SEL button two or
more times to select the desired zone and then press one of the INPUT
buttons within 10 seconds.
Note:
See the section on Zone 2–4 operations for details of
selecting a source for the remote zone.
Selecting a Source from the Remote
AJU
To select a source for LISTENING in the main room:
press and
hold one of the DEVICE/INPUT buttons for more than one second. To
select the MULTI INPUT, press and hold the EXT button.
Note:
A short press of a DEVICE/INPUT button changes the
remote control device only, but does not change the source input.
To select a source for RECORDING:
Press the REC button
(“RECORD” appears in the front panel display). Then, press and hold
one of the DEVICE/INPUT buttons within 10 seconds.
Alternatively, you can press the REC button and then use the +/– buttons
to scroll through the available source options. Select any input (CD,
TUNER, TAPE, or VIDEO 1–5). Selecting the SOURCE option links the
recording source to the input selected for main room listening. Whatever
input is selected for listening is also sent to the record outputs.
To select a source for Zone 2, 3 or 4:
Press the REC button two or
more times to select a zone. Then, press and hold one of the DEVICE/
INPUT buttons within 10 seconds.
Alternatively, you can press the REC button to select a zone and then
use the +/– buttons to scroll through the available source options. Select
any input (CD, TUNER, TAPE, or VIDEO 1–5). Selecting the SOURCE
option links the Zone 2, 3 or 4 source to the input selected for main room
listening. Whatever input is selected for the main room is also sent to the
remote zone outputs.
Note:
The RR-1061 remote control can be set to send individual
IR commands for each zone. Please refer to the setup manual
supplied with the RR-1061 to program this function.
RSX-1560 English v2.indd 29
29/9/08 15:16:02