28
Important safety instructions
Read the whole instruction for use before you start using
●
your jug blender.
The jug blender is intended for domestic usage only.
●
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
Connect the appliance to 220 - 240 V mains supply.
●
During first start-up the appliances can emit some
●
odours. It is a normal phenomenon, which should be
over after a time.
Always place the appliance on flat, plain surface.
●
Always unplug the appliance when it is not in use and
●
before cleaning.
Do not unplug by pulling on cord.
●
The supplying cord shall not be hanged over the edge of
●
the table or board, nor touch any hot surface.
Do not operate the appliance if the cord, the housing or
●
the handle is visibly damaged. In such a case, return the
appliance to a service center.
If the non-detachable part of the cord is damaged,
it should be replaced by the producer or at a proper
service point or by a qualified person in order to avoid
any hazards.
The appliance should be repaired by trained staff only.
Improper repair can result in serious hazard for a user. In
case of defects we recommend you to contact qualified
service desk.
Do not immerse motor housing in water or any other
●
liquid; do not use it in bathroom and outdoors.
Do not use jug blender without feeder opening stopper.
●
Do not fill the jug in with boiling liquids.
●
Do not put your hands inside the jug, even if it is removed
●
for cleaning, as the cutting blades are still dangerous –
very sharp.
Do not put any objects (spoon, etc.) into the jug, when
●
the blender is connected to power supply.
Keep the jug blender and supplying cord away from hot
●
surfaces and burners.
If it is possible, store the jug blender away from direct
●
sun radiation and glow-like light.
Never store with lid closed on the blender jug.
●
Do not overflow the jug. In case the liquid gets under
●
the motor housing, it can be vacuumed into the motor,
causing its damage.
Do not fill the jug over 1000 ml mark – in such case, the
●
content of the jug can lift the lid when the motor starts up
After 2 minutes operation stop the appliance for at least
●
minute to let the motor cool down. You can repeat this
cycle maximum10 times.
Do not operate when the jug is empty, as it can get
●
overheated.
The appliance is equipped with motor overheating
●
protection. In case the motor working temperature is too
high, the blender shall stop operating. After cooling the
operation shall come back automatically.
Do not wash the cutting blades directly with hand.
●
Use the soft brush for washing metal parts, especially
●
the sharp blades.
This appliance is not intended for use by persons
●
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
●
play with the appliance.
The temperature of mixed ingredients should not exceed
●
60°C.
Make sure you understand well above mentioned
instructions.
Technical specification
Technical parameters are indicated on the nameplate of the
product.
Admissible time of uninterrupted operation: 2 minutes.
Time of interval before next operation: 10 minutes.
Maximum noise level: 78 dB/A.
The jug blender is built in 2nd isolation class.
It does not require connection to the socket equipped with
grounding pin.
The jug blender meets the requirements of standards in
force.
The appliance meets the requirements of the directives:
Low Voltage Device (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) – 2004/108/EC.
–
The product is marked with CE mark on the nameplate.
The outline of the appliance
(Fig. A)
1
Lid overlay
2
Lid sieve
3
Blender jug
4
Speed control knob
5
Lid
6
Blade unit
7
Attachment for centrifuging juice of soft fruit and soya
beans
8
Gasket
9
Power cord compartment
10
Motor unit
11
Anti-slip foot
EN
