Инструкция для ZYXEL ES3500-24HP

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

Chapter 3 Hardware Overview

ES3500 Series User’s Guide

30

3.1.1  Console Port

For local management, you can use a computer with terminal emulation software configured to the 
following parameters:

• VT100
• Terminal emulation
• 9600 bps
• No parity, 8 data bits, 1 stop bit
• No flow control

Connect the male 9-pin end of the console cable to the console port of the Switch. Connect the 
female end to a serial port (COM1, COM2 or other COM port) of your computer. 

3.1.2  Ethernet Ports 

The Switch has 10/100 Mbps auto-negotiating, auto-crossover Ethernet ports. In 10/100 Mbps Fast 
Ethernet, the speed can be 10 Mbps or 100 Mbps and the duplex mode can be half duplex or full 
duplex. 

An auto-negotiating port can detect and adjust to the optimum Ethernet speed (10/100 Mbps) and 
duplex mode (full duplex or half duplex) of the connected device.

An auto-crossover (auto-MDI/MDI-X) port automatically works with a straight-through or crossover 
Ethernet cable.

The Switch has several dual-personality interfaces, (see 

Figure 9 on page 28

 an

Figure 13 on page 

29

), each of which consists of an RJ-45 Ethernet port and SFP slot pair. The Switch activates one 

connection of each RJ-45 and SFP slot pair. The SFP slots have priority over the RJ-45 ports. This 
means that if an RJ-45 port and the corresponding SFP slot are connected at the same time, the RJ-
45 port will be disabled.

When auto-negotiation is turned on, a Ethernet port negotiates with the peer automatically to 
determine the connection speed and duplex mode. If the peer Ethernet port does not support auto-
negotiation or turns off this feature, the Switch determines the connection speed by detecting the 
signal on the cable and using half duplex mode. When the Switch’s auto-negotiation is turned off, 
an Ethernet port uses the pre-configured speed and duplex mode when making a connection, thus 
requiring you to make sure that the settings of the peer Ethernet port are the same in order to 
connect.

3.1.2.1  Default Ethernet Negotiation Settings

The factory default negotiation settings for the Gigabit ports on the Switch are:

• Speed: Auto 
• Duplex:  Auto
• Flow control: Off
• Link Aggregation: Disabled

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
Оглавление инструкции

Document Outline