![background image](/i/dell/157615/dell-3100cn/h/dell-3100cn-111.png)
l
When there are multiple tab codes in one line, the tab position may be off as a result of automatic line feed. In such case, use the
-I
or
-w
option.
l
The number of columns specified by the
-w
option is not the actual number of printed characters. The actual number of single-byte characters to be
printed is derived by deducting the output column position (outcolumns) specified by the o option from the number of columns specified by the
-w
option.
The -mg option cannot be specified when
-w
,
-l
,
-o
, and
-L
option are specified.
The start positions of margin of the margin command (
-mg=
u:b:r:l
) are not set against the edge of the paper. The margins are set against the printable
area of the paper allowed by the printer.
Use the
-ps
option only when a PostScript file that contains no
%!
at the beginning of the file is used as the PostScript file. If a normal text file is input, it
will not function correctly.
l
In HP-UX, txt2ps2 considers files written by PostScript that contain
%!
at the beginning of the file as the PostScript files. To print PostScript files as text
files, specify the
TX
option. With this option, PostScript files will be processed as text files.
sunras2ps2 (Solaris)
Format
/usr/local/dellbin3100cn/sunras2ps2 [-d] [-D] [-I
tray-input
]
[-t] [-r] [-n] [-l=
left
,
bottom
] [-s=
width
,
height
]
[-S=
width
]
[-E] [-Nc=
copies
]
[-
Hd=
position: format
]
[-Hf
font
]
[-MSI]
[
-M=
type
]
[
-Mfo
=mode
]
[
-Po
n
]
[
-St=
mode
]
[
-Sp]
[
-Sb] [-Cm=
mode
]
[-Pr=
mode
]
[-Cc=
mode
]
[
-Gc=
mode
]
[
-Sc=
mode
]
[
-
Gg=
mode
]
[-Ct] [filename...]
Function
Reads SunRaster data, converts it to the PostScript language program and writes to standard output. If the filename is not specified, the standard input will
be taken as the command input. SunRaster files with a pixel depth of 1, 8, 24, and 32 bits can be specified.
sunran2ps2 takes filename as having been created in 72dpi and calculates the output size. Thus, to convert SunRaster files created in other resolutions,
specify the size option (
-s
,
-S
) explicitly.
Option
-d
Enables the short-edge binding feature. When it is specified, the printing direction or position will be adjusted and both sides of the paper printed so
that the shorter edge of the pages can be bound. This option is available only when the optional duplex module is installed on the printer.
-D
Enables the long-edge binding feature. When it is specified, the printing direction or position will be adjusted and both sides of the paper printed so that
the longer edge of the pages can be bound. This option is available only when the optional duplex module is installed on the printer.
-I
tray-input
Specifies the paper tray.
A paper tray can be selected by directly specifying a tray or by specifying a paper size.
When a paper size is specified, the tray loaded with paper of the specified size will be found and selected automatically.
The parameters for selecting a paper tray are as follows.
1
Feed paper from tray 1 (standard 250-sheet tray module).
2
Feed paper from tray 2 (optional 250-sheet tray module or 500-sheet tray module).
A4
Feed paper from the tray loaded with A4 (210 x 297 mm).