![background image](/i/dell/157615/dell-3100cn/h/dell-3100cn-061.png)
6.
Remove the screws of the straps on the left and right of the module from the optional duplex module.
7.
Remove the optional duplex module from the printer.
8.
Gently push both sides of the bottom of the paper cover to install it.
9.
Open the inner rear cover. Attach the cover, which you have kept since installing the duplex module, until it clicks, and then close the rear cover.
Оглавление инструкции
- Страница 1 из 220
Printer Settings You can change most printer settings from your software program or printer driver. If your printer is attached to the network, you can change settings from the Dell Printer Configuration Web Tool. To launch the Dell Printer Configuration Web Tool, type the printer IP address in - Страница 2 из 220
Each menu item has a list of values for the menu item. A value can be: l A phrase or word to describe a setting l A numerical value that can be changed l An On or Off setting l Press at the same time. This will recover the factory default menu settings. 4. Press 5. Press . This enables the setting - Страница 3 из 220
3. Press until Network appears, and then press or . 4. Press until Init NVRAM appears, and then press 5. The Init NVRAM Are you sure? message appears on the operator panel. Press 6. Turn off the printer, and then on again. or . . - Страница 4 из 220
Installing the Optional Tray Module CAUTION: If you are adding an optional 250-sheet tray module or 500-sheet tray module after setting up the printer, be sure to turn off the printer, unplug the power cable, and disconnect all cables from the back of the printer before completing these tasks. l - Страница 5 из 220
6. Attach the trays together by installing the standard tray you just removed on top and inserting the two screws provided. Tighten the screws with a coin until they are secure. 7. Place the printer on top of the tray modules. 8. Lock the trays into place by removing the top tray from the tray - Страница 6 из 220
9. 10. Replace all trays and load the paper. Turn on the printer. NOTE: The printer will automatically detect the attached trays but will not detect the paper type. 11. Print a Printer Settings page to verify the optional 250-sheet tray module or 500-sheet tray module is installed correctly. a. - Страница 7 из 220
4. Click Apply, and then click OK. 5. Close the Printers folder. If Get Information from Printer is unavailable, follow these steps: 1. In the Items list box of the Options tab, find Option Tray Module. 2. Change the setting from Not Available to 250 Sheet Tray Module (A4/Letter Cassette), 250 - Страница 8 из 220
Safety and Regulatory Information Safety Information Regulatory Information Noise Emissions Levels Laser Notice Energy Star Safety Information CAUTION: Read and follow all safety instructions in your Owner's Manual prior to setting up and operating your printer. Regulatory Information Federal - Страница 9 из 220
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis de Conformité aux Normes de l'industrie du Canada Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European - Страница 10 из 220
NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM): Exporter: Dell Inc. One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, S.A. de C.V. Paseo de - Страница 11 из 220
radiation above a Class I level during normal operation, user maintenance, or prescribed service condition. Energy Star ENERGY STAR® Compliance Certain configurations of Dell printers comply with the requirements set forth by the Environmental Protection Agency (EPA) for energy-efficient printers. - Страница 12 из 220
Printing With CUPS (Linux) This section provides information for printing or setting up the printer driver with CUPS (Common UNIX Printing System) on Red Hat 8/9 and SuSE 8.2/9. Operation on Red Hat 8/9 Operation on SuSE 8.2/9 Operation on Red Hat 8/9 Setting Overview If you use Red Hat 8, you need - Страница 13 из 220
The Printing Support Package Details window appears. 5. Select the CUPS check box in Extra Packages, and then click Close. 6. Click Update in the Add or Remove Packages window. 7. Click Continue in the Completed System Preparation window. Installation starts. When you are requested to insert the - Страница 14 из 220
The browser is activated and the CUPS window appears. NOTE: For Red Hat 8, select GNOME Menu ® System Tools ® CUPS Printer Configuration. 2. Click Manage Printers. 3. Click Configure Printer of the queue for which you want to specify the printing options. 4. Type root as the user name, and type the - Страница 15 из 220
5. Confirm the settings in Printer overview, and then click OK. 6. Click Finish. 7. Click Continue. Setting Up the Queue on SuSE 9 1. Select Start Applications ® System ® YaST. 2. Type the administrator's password. YaST Control Center is activated. 3. Select Hardware from Printer. 4. Printer setup: - Страница 16 из 220
2. Printer setup: Autodetected printers is activated. 3. Click Change. 4. Select the printer you wan to set to default, and then click Set as default. 5. Click Finish. NOTE: For SuSE 8.2, also click Continue. Specifying the Printing Options You can specify the printing options such as color mode or - Страница 17 из 220
Installing the Optional Duplex Module To Make Duplexing the Default for All Print Jobs Installing Cards NOTE: If you are adding an optional duplex module after setting up the printer, be sure to turn off the printer, unplug the power cable, and disconnect all the cables from the back of the printer - Страница 18 из 220
5. Attach the straps to the left and right side of the printer, and then close the optional duplex module. 6. Tighten the screws on the bottom left and right while firmly holding the optional duplex module in a closed position. 7. Open the optional duplex module. Remove the connector cover, and - Страница 19 из 220
9. Attach the new connector cover supplied with the duplex module. When installing the supplied 64MB memory card, see "Installing a Memory Card". 10. Turn on the printer. 11. Make sure the optional duplex module is properly installed. a. Press Menu. b. Press until Configure appears, and then press - Страница 20 из 220
5. Close the Printers folder. If Get Information from Printer is unavailable, follow these steps: 1. In the Items list box of the Options tab, find Duplex Module. 2. Change the setting from Not Available to Available. 3. Click Memory Capacity, and then select an appropriate numerical value. NOTE: - Страница 21 из 220
You can set up your driver to use duplexing on all print jobs. If you do not want duplexing for a specific print job, you can override this feature. 1. In Windows Server 2003 and Windows XP, click Start ® Printers and Faxes. In all other operating systems, click Start ® Settings ® Printers. 2. - Страница 22 из 220
5. Reattach the control board cover to the printer. Installing a Multi Protocol Card A multi protocol card allows you to use the following network protocols. Network protocol Supported OSes IPP Windows Me/2000/XP/Server 2003 SMB Windows 95/98/Me/NT 4.0/2000/XP/Server 2003 NetWare (IPX/SPX) - Страница 23 из 220
5. Reattach the control board cover to the printer. - Страница 24 из 220
Understanding Printer Menus When your printer is configured as a network printer available to a number of users, the access to the Configure menus can be limited. This prevents other users from using the operator panel to inadvertently change a printer user default that has been set by the - Страница 25 из 220
Use the Tray Settings menu to define the print media loaded in each tray. NOTE: Values marked by an asterisk (*) are the factory default menu settings. Paper Type Purpose: To specify the type of paper loaded in each tray. Values: Tray 1 Plain 1 Plain 2 Tray 2* 1 Plain 1 Plain 2 MPF Plain 1 Plain 2 - Страница 26 из 220
8.5 x 13"*3 Tray 2* 4 Letter* 1 B5* 2 A5* 2 A4* 1 Executive* 2 Legal*2, 3 8.5 x 13"*2, 3 Letter MPF B5 A5 A4 Executive Legal 8.5 x 13" Envelope #10 Monarch DL C5 Free Size* Monarch LEF DL LEF *1 *2 *3 *4 Denotes country-specific factory default values. Available for the optional 250-sheet tray - Страница 27 из 220
Use the Basic Settings menu to configure the basic printer settings. NOTE: Values marked by an asterisk (*) are the factory default menu settings. Power Saver Time Purpose: To specify the amount of time the printer waits after a job is printed before it goes into the power saver mode. Values: 1–60 - Страница 28 из 220
5–300 sec Specifies the amount of time the printer waits for additional data before it cancels the job. 30 sec* Panel Language Purpose: To determine the language of the text on the operator panel screen. Values: English* French Italian German Spanish Auto Log Print Purpose: To specify whether the - Страница 29 из 220
Prints the user ID on the top right of the page. Top Right Prints the user ID on the bottom left of the page. Bottom Left Bottom Right Prints the user ID on the bottom right of the page. NOTE: When printing on DL size paper, a part of the user ID may not be printed correctly. Text Print Purpose: To - Страница 30 из 220
Values: Does not allocate memory to the RAM Disk file system. Proof Print jobs will abort and be recorded to the job log. Off* Allocates memory to the RAM Disk file system automatically. On NOTE: The RAM Disk menu is only displayed when 320 MB or more of additional RAM is installed on the printer. - Страница 31 из 220
Values: Plain 1 0-15 5* Plain 2 0-15 5* Transparency 0-15 5* Covers 1 0-15 5* Covers 2 0-15 5* Label 0-15 5* Coated 1 0-15 5* Coated 2 0-15 5* Envelope 0-15 5* Init NVRAM Purpose: To initialize the NV (non-volatile) memory. After executing this function and rebooting the printer, all the menu - Страница 32 из 220
Values: Disables the use of refilled toner cartridges. Off* Enables the use of refilled toner cartridges. On Parallel The Parallel menu can be adjusted to configure the parallel interface. NOTE: Values marked by an asterisk (*) are the factory default menu settings. ECP Purpose: To specify the ECP - Страница 33 из 220
Use the Reports menu to print various types of reports and lists. Printer Settings Purpose: To print a list of the current user default values, the installed options, the amount of installed printer memory, and the status of printer supplies. Panel Settings Purpose: To print a detailed list of all - Страница 34 из 220
Purpose: To print a list of all files that are stored as Secure and Proof Print in the RAM Disk. Network Use the Network menu to change printer settings affecting jobs sent to the printer through a network port. Ethernet Purpose: To specify the communication speed and the duplex settings of - Страница 35 из 220
Protocol Purpose: To enable or disable each item. The change becomes effective after the printer is turned off and then on again. Values: LPD On* Off Port9100 On* Off IPP*1 On* Off SMB TCP/IP* 1 On* Off SMB NetBEUI* 1 On* Off FTP On* Off Netware* 1 On* Off SNMP UDP On* Off IPX*1 On* Off E-Mail - Страница 36 из 220
Purpose: To configure the IPX/SPX settings. The change becomes effective after the printer is turned off and then on again. Values: Automatically sets the frame type. Auto* Uses the Ethernet frame type. Ethernet II Ethernet 802.3 Ethernet 802.2 Ethernet SNAP Uses the IEEE802.3 frame type. Uses the - Страница 37 из 220
To specify PostScript communication protocol for each interface. You can configure Adobe Protocol settings for Network. The change becomes effective after the printer is turned off and then on again. Values: Auto* RAW Standard Used when auto-detecting the PostScript communication protocol. Used - Страница 38 из 220
Values: Auto* Tray 1 Tray 2*1 MPF Automatically selects a tray according to the paper size and type settings of the job being printed except for the multipurpose feeder. The paper is fed from the standard 250-sheet tray module. The paper is fed from the optional 250-sheet tray module or 500-sheet - Страница 39 из 220
To set duplexing as the default for all print jobs. (Select Duplex from the printer driver to duplex only specific jobs.) Values: Prints on one side of the paper. Duplex Print Off* Prints on both sides of the paper. On Binding Long Edge* Short Edge Assumes binding along the long edge of the page. - Страница 40 из 220
CourierPS BdOb SymbolPS Palatino Roman Palatino It Palatino Bd Palatino BdIt ITCBookman Lt ITCBookman LtIt ITCBookmanDm ITCBookmanDm It HelveticaNr HelveticaNr Ob HelveticaNr Bd HelveticaNrBdOb N C Schbk Roman N C Schbk It N C Schbk Bd N C Schbk BdIt ITC A G Go Bk ITC A G Go BkOb ITC A G Go Dm ITC - Страница 41 из 220
12.00* Font size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch. NOTE: The Font Size menu is only displayed for typographic fonts. See also: "Pitch and Point Size" Font Pitch Purpose: To specify the font pitch for scalable monospaced fonts. - Страница 42 из 220
"Orientation," "Paper Size" Quantity Purpose: To set the number of copies you want for the printer default value. (Set the number of copies required for a specific job from the printer driver. Values selected from the printer driver always override values selected from the operator panel.) Values: - Страница 43 из 220
Values: Does not print in the draft mode. Off* Prints in the draft mode. On Line Termination Purpose: To add the line termination commands. Values: Off* The line termination command is not added. CR=CR, LF=LF, FF=FF Add-LF The LF command is added. CR=CR-LF, LF=LF, FF=FF The CR command is added. - Страница 44 из 220
Discards the print job without printing an error message. On* Prints an error message before it discards the job. Off NOTE: This instructions from the PS driver override the settings specified on the operator panel. PS Job Timeout Purpose: To specify the execution time for one PostScript job. - Страница 45 из 220
Values: Off* On Does not limit access to the menus. Limits access to the menus. Change Password Purpose: To set a password to limit access to the menus. Values: 0000–9999 0000* Setting of Panel Lock This feature prevents unauthorized personnel from changing settings made by the printer - Страница 46 из 220
3. Press until Security appears, and then press 4. Panel Lock is displayed. Press 5. Press or . until Off appears, and then press . or . - Страница 47 из 220
Printing This chapter covers tips for printing, how to print certain lists of information from your printer, and how to cancel a job. Tips for Successful Printing Sending a Job to Print Canceling a Print Job Printing a Printer Settings Page Printing a Font Sample List Using the Print and Hold - Страница 48 из 220
Canceling a Print Job There are several methods for canceling a print job. Canceling From the Printer Operator Panel To cancel a print job after it has started printing: 1. Press Cancel. Printing is canceled. Canceling a Job From the Computer Running Windows Canceling a Job From the Taskbar When - Страница 49 из 220
1. Press Menu. 2. Press until Configure appears, and then press 3. Press until Reports appears, and then press 4. Press until either PCL Fonts List or PS Fonts List appears. 5. or or . . l Select PCL Fonts List to print a listing of the fonts available to the PCL emulator. l Select PS Fonts List to - Страница 50 из 220
4. Press until your user name appears, and then press or . 5. Press until the job you want to print appears, and then press or 6. Press until the way you want to print appears, and then press . 7. Enter the print quantity, and then press . . When you select Select All in step 5 and the print - Страница 51 из 220
Print Media Guidelines Print media is paper, transparencies, labels, envelopes, coated paper among others. Your printer provides high-quality printing on a variety of print media. Selecting the appropriate print media for your printer helps avoid printing troubles. This section describes how to - Страница 52 из 220
Most high-quality xerographic paper is made from 100% chemically pulped wood. Paper containing fibers such as cotton possess characteristics that can result in degraded paper handling. Recommended Paper To ensure the best print quality and feed reliability, use 75 g/m2 (20 lb) xerographic paper. - Страница 53 из 220
l Flex paper back and forth, and then fan them. Straighten the edges of the stack on a level surface. l When curl is excessive, with plain paper, turn it over and reset it. Selecting Preprinted Forms and Letterhead When selecting preprinted forms and letterhead paper for the printer: l Use long - Страница 54 из 220
To select and use pre-punched paper: l Test paper from several manufacturers before ordering and using large quantities of pre-punched paper. l Paper should be punched at the paper manufacturer and not drilled into paper already packaged in a ream. Drilled paper can cause jams when multiple sheets - Страница 55 из 220
l Contain windows, holes, perforations, cutouts, embossing l Use metal clasps, string ties, or metal folding bars l Have an interlocking design l Have postage stamps attached l Have any exposed adhesive when the flap is in the sealed or closed position l Have nicked edges or bent corners l Have - Страница 56 из 220
For proper print media storage, the following guidelines help avoid media feeding problems and uneven print quality. l For best results, store print media in an environment where the temperature is approximately 21°C (70°F) and the relative humidity is 40%. l Store cartons of print media on a - Страница 57 из 220
Setup Paper Type Paper type Weight (gsm) Remarks Plain1 60-80 - Plain2 81-105 - Covers1 106-163 - Covers2 164-216 - Coated1 106-163 BJP (Bubble Jet Printer) paper cannot be used. Coated2 164-216 BJP (Bubble Jet Printer) paper cannot be used. Transparency - BJP (Bubble Jet Printer) paper cannot be - Страница 58 из 220
Setting Up for Shared Printing Point and Print Peer-to-Peer You can share your new printer on the network using the Drivers and Utilities CD that shipped with your printer, or using Microsoft's point and print or peer-topeer method. However, if you use one of the Microsoft methods, you will not - Страница 59 из 220
1. Click Start ® Settings ® Printers. 2. Click Add Printer to launch the Add Printer wizard. 3. Click Network Print Server. 4. Select the network printer from the Shared printers list. If the printer is not listed, type in the path of the printer in the text box. For example: \\<server host - Страница 60 из 220
Removing Options If the printer location needs to change or the printer and print media handling options need to be shipped to a new location, all print media handling options must be removed from the printer. For shipping, pack the printer and print media handling options securely to avoid damage. - Страница 61 из 220
6. Remove the screws of the straps on the left and right of the module from the optional duplex module. 7. Remove the optional duplex module from the printer. 8. Gently push both sides of the bottom of the paper cover to install it. 9. Open the inner rear cover. Attach the cover, which you have - Страница 62 из 220
Removing Optional Tray Modules CAUTION: To lift the printer safely and replace the optional 250-sheet tray module or 500-sheet tray module requires two people to stand in front (operator panel side) and behind the printer and to lift at the same time. Do not try to lift the printer from the sides. - Страница 63 из 220
5. Remove the optional 250-sheet tray module or 500-sheet tray module. 6. Place the printer on top of the standard 250-sheet tray module. 7. Lock the standard 250-sheet tray module into place by removing the tray from the tray module and rotating the locking mechanism as shown in the graphic. 8. - Страница 64 из 220
1. Make sure that the printer is turned off. 2. Remove the control board cover on the left side of the printer by pulling the notch. 3. Push the knobs on both sides of the slot outward. Remove the memory card from the slot. 4. Reattach the control board cover to the printer. For more information, - Страница 65 из 220
3. Loosen the two screws from the back side of the printer. 4. Hold the bottom of the multi protocol card and remove it from the control board. 5. Reattach the control board cover to the printer. For more information, see "Installing Cards". - Страница 66 из 220
Troubleshooting Troubleshooting Guide This section consists of the following instructions. Configuration of your printer instructions User Settings l Menu Map l Setup printing Letter Plain 1 from Multipurpose Feeder l Setup printing Letter Plain 1 from Tray 1 l Setup printing Letter Plain 1 from - Страница 67 из 220
Basic Printer Problems Some printer problems can be easy to resolve. If a problem occurs with your printer, check each the following: l If a message displays on the operator panel, see "Understanding Printer Messages." l The printer power cable is plugged into the printer and a properly grounded - Страница 68 из 220
Print media misfeeds or multiple feeds occur. Make sure the print media you are using meets the specifications for your printer. See "Print Media Supported" for more information. Flex print media before loading it in any of the sources. Make sure the print media is loaded correctly. Make sure the - Страница 69 из 220
"Paper Type." · Verify that the print media is within the printer specifications. See "Print Media Supported." Toner spots appear on the page/printing is blurred. · Check the toner cartridge to make sure it is installed correctly. · Change the toner cartridge. See "Replacing the Toner Cartridge." - Страница 70 из 220
The job prints, but the top and side margins are incorrect. · Make sure the Paper Size setting in the Tray Settings is correct. Printing on both ends of the transparencies is faded. · This occurs when the printer is operating in a location where relative humidity reaches 85% or more. Adjust the - Страница 71 из 220
Contacting Service When you call for printer service, be prepared to describe the problem you are experiencing or the error message on the display. You need to know your printer model type and serial number. See the label on the back of the printer near the power cable for this information. - Страница 72 из 220
11. Now press MENU to get back to Tray Settings/Paper Size. 12. Press to get to Paper Type. 13. Press to select Paper Type. 14. Press to get to MPF. 15. Press to select MPF. 16. Using and 17. Press SELECT, once Plain 1 is displayed on the lower line. 18. Now we have the MPF Type set to Plain 1. 19. - Страница 73 из 220
11. Now press MENU to get back to Tray Settings/Paper Size. 12. Press to get to Paper Type. 13. Press to select Paper Type. 14. Press to get to Tray 1. 15. Press to select Tray 1. 16. Using and 17. Press SELECT, once Plain 1 is displayed on the lower line. 18. Now we have the Tray 1 Type set to - Страница 74 из 220
11. Now press MENU to get back to Tray Settings/Paper Size. 12. Press to get to Paper Type. 13. Press to select Paper Type. 14. Press to get to Tray 2. 15. Press to select Tray 2. 16. Using and 17. Press SELECT, once Plain 1 is displayed on the lower line. 18. Now we have the Tray 2 Type set to - Страница 75 из 220
11. Now press MENU to get back to Tray Settings/Paper Size. 12. Press to get to Paper Type. 13. Press to select Paper Type. 14. Press to get to MPF. 15. Press to select MPF. 16. Using and 17. Press SELECT, once Plain 1 is displayed on the lower line. 18. Now we have the MPF Type set to Plain 1. 19. - Страница 76 из 220
11. Now press MENU to get back to Tray Settings/Paper Size. 12. Press to get to Paper Type. 13. Press to select Paper Type. 14. Press to get to MPF. 15. Press to select MPF. 16. Using and 17. Press SELECT, once Plain 1 is displayed on the lower line. 18. Now we have the MPF Type set to Plain 1. 19. - Страница 77 из 220
11. Now we have the MPF Size set to Letter. 12. Now press MENU to get back to Tray Settings/Paper Size. 13. Press to get to Paper Type. 14. Press to select Paper Type. 15. Press to get to MPF. 16. Press to select MPF. 17. Using and 18. Press SELECT, once Plain 1 is displayed on the lower line. 19. - Страница 78 из 220
A local printer is a printer attached to your computer or a print server using a USB or parallel cable. Installing Printer Drivers Connecting the Printer to the Computer Before Inserting the Drivers and Utilities CD Windows 98, Me, 2000, XP, and Server 2003 1. Connect your printer to your computer. - Страница 79 из 220
8. Select either the Typical Installation or Custom Installation checkbox, and then click Next. If you select Custom Installation, you can select the specific software you want to install. 9. When using Windows 98 or Me, the Adobe License Agreement appears, click to accept the agreement and then - Страница 80 из 220
9. If you want to restrict color printing, select the appropriate Color Track option. Enter the password. 10. If the PostScript (PS) Driver is available and you want to install it, click on the check box. 11. Click Next. 12. Select the software and documentation you want to install. You can specify - Страница 81 из 220
Use the Customer Mode to locate the unit in the printer that causes a problem. Diagnostic Menu Map (Customer Mode) 1. Turn off the printer. 2. Turn on the printer while holding down The Customer Mode menu appears. and . Testing "Print Quality" "Print Quality" is used to diagnose print quality - Страница 82 из 220
After you output the test results, contact Dell. Clear NVRAM You can restore the original factory default menu settings by initializing NVRAM. 1. Press Menu. 2. Press until Configure appears, and then press 3. Press until Maintenance appears, and then press 4. Press until Init NVRAM appears, and - Страница 83 из 220
3. Grab the drum cartridge by the handle, and pull it up and out. CAUTION: Do not touch inside the printer with your hands. Some parts may be hot. Allow time for the printer to cool before attempting to remove parts in this area. 4. Remove the protective sheet from the drum cartridge. CAUTION: Do - Страница 84 из 220
7. Close the top cover. How to install the Toner Cartridge CAUTION: Before performing any of the following procedures, read and follow the safety instructions in your Owner's Manual. In addition to the toner level indicator that appears each time you send a job to print, a message appears on the - Страница 85 из 220
2. Push up the handhold on the right to unlock the cartridge. 3. Hold the toner cartridge and pull out the cartridge. CAUTION: Do not touch inside the printer with your hands. Some parts may be hot. 4. Make sure the color of the toner cartridge matches the slot on the toner cartridge carrier. - Страница 86 из 220
6. To insert the toner cartridge, align the arrows on the cartridge with the corresponding arrows on the printer. Guide the cartridge in until it snaps into place, and then push down the handhold to lock the cartridge in place. 7. If replacing just one toner cartridge, close the front door and you - Страница 87 из 220
2. Pull out the slide bar that is inside the printer on the right side until it stops. The access window cover slides open. 3. Hold the cleaning rod and push the rod in and pull out once to clean inside the printer. 4. Push the slide bar back to its original position. 5. Close the front door. - Страница 88 из 220
Enterprise Console Management Modules The following enterprise console management modules and user's manuals are available on your Drivers and Utilities CD under \Utilities\SnapIns: l IBM Tivoli® NetView® l CA Unicenter® l HP OpenView® To use the modules, go to the following directory on your CD - Страница 89 из 220
Printing With UX Filter (UNIX/Linux) Overview Installing the UX Filter Uninstalling the UX Filter Printing and Using the Utilities Precautions and Limitations Overview The UX Filter This section describes the features of the UX filter and its operating environment. Features The UX filter is a - Страница 90 из 220
Before Using UX Filter Check the following items before using the UX filter. Before setting up the workstation, set up the printer as follows. 1. Make sure the lpd port is working or not when using the network environment. If the lpd port is not working, set LPD to On on the operator panel. - Страница 91 из 220
/usr/share/man/man1 dell3100cn.fd dell3100cn filter description file for Dell Laser Printer 3100cn dellpostio.fd dellpostio Filter description file delldownload.fd delldownload Filter description file dellpsif.1 man file for dellpsif sunras2ps2.1 man file for sunras2ps2 txt2ps2.1 man file for - Страница 92 из 220
Solaris 1. Setup the printer and network. 2. Insert the Drivers and Utilities CD into the local workstation. 3. Run the installer and begin the installation. 4. Print for testing the printer. HP-UX 1. Setup the printer and network. 2. Insert the Drivers and Utilities CD into the local workstation. - Страница 93 из 220
/etc/printcap.local or /etc/printcap lp:\ :bk:\ :bkf:\ :lpd_bounce=true:\ :sd=/var/spool/lpd/lp:\ :af=/var/spool/lpd/lp/lp.acct:\ :lf=/var/spool/lpd/lp/log:\ :rm=PrinterHostName:\ :rp=ps:\ :if=/usr/local/dellbin3100cn/dellpsif: NOTICE: The directory to spool can be created in the partition with - Страница 94 из 220
9. Type the printer name to be registered with the system. Enter printer-name? [dell3100cn] : dell3100cn Printer-name is 'dell3100cn' (y/n)[y] : y 10. Specify the directory to install the utility. To install into /usr/local/dellbin3100cn, press the <Enter> key. To change the directory, specify one. - Страница 95 из 220
access the utility. As this process is automatically executed, no input is required. With the above steps, the installation is complete. Uninstalling the UX Filter About Uninstalling The UX filter does not come with an uninstaller. To uninstall the UX filter, follow the following procedure. NOTICE: - Страница 96 из 220
Printing and Using the Utilities Printing (Linux) This section provides information on printing with the filter. To print, specify the printer registered with /etc/printcap as the output destination. Printing From Linux To print to the default printer: If the printer is registered as the default - Страница 97 из 220
% lpr -Pa4d filename Printing (Solaris) This section provides information on printing that makes use of the filter. To print from Solaris, specify the printer registered during the installation of filters as the output destination. NOTICE: To use the lp command, make sure the operating environment - Страница 98 из 220
This option converts text to single-byte text and sets printing to start from the nth column. -y outline=n Sets printing to start from the nth line. -y font=font Sets the font for printing single-byte alphanumeric characters. If the font specified is not available for the printer, the default fonts - Страница 99 из 220
Feed paper from the tray loaded with MxNinches defined by users. Possible range specified: Width: 3.54 to 8.50 inches Length: 5.50 to 14.0 inches If this option is not specified or the tray specified tray is not available, feed paper from the default tray. -y toner_save Turns on the save toner mode - Страница 100 из 220
Portrait (Rotated) -y po=n Specifies Alternate Tray. Available Alternate Trays are as follows. 0 Use Printer Settings 1 Display Message 2 Feed from Multipurpose Feeder 3 Use Nearest Size (Adjust to Fit) 4 Use Larger Size (Adjust to Fit) 5 Use Nearest Size (No Zoom) 6 Use Larger Size (No Zoom) -y - Страница 101 из 220
Off 1 Photo 2 sRGB 3 Standard/ Normal 4 Presentation This option is available only for color printing. -y gc=mode Specifies RGB Gamma Correction. Available RGB Gamma Corrections are as follows. 1.0 1.0 1.4 1.4 1.8 1.8 2.2 2.2 2.6 2.6 off Off -y sc=mode Specifies Screen. Available Screens are as - Страница 102 из 220
To print to the default printer: If the printer is registered as the default printer, the name of the printer can be shortened and specified as shown in the following example. % lp filename To print to other printers: To print to a printer named dell3100cn, type as follows. % lp -d dell3100cn - Страница 103 из 220
according to the line/column specified. txt2ps2 interprets the following control codes. Other control codes/undefined codes will be converted to octal numbers and output as-is. LF Line feed FF Form feed (modifiable by option) TAB 8-column tab stop (modifiable by option) BS Backspace 1 character - Страница 104 из 220
LG Feed paper from the tray loaded with Legal (8.5 x 14 inches). EX Feed paper from the tray loaded with Executive (7.25 x 10.5 inches). MO Feed paper from the tray loaded with Monarch (3.875 x 7.5 inches). COM10 Feed paper from the tray loaded with Envelope #10 (4.125 x 9.5 inches). DL Feed paper - Страница 105 из 220
-Loutlines Prints text from the outline columns. -en Expands horizontal tabs to n columns (space). The default is 8. -ssize Specifies the font size as point size. The default is 10. -E This function turns on the image enhancement function. In some cases, this option will be ignored. -ffont Sets the - Страница 106 из 220
format specifies the contents and the order to output. This option is omissible. If this option is omitted, uh is specified as the default value. u User name h Host name t Date and time If the output contents are specified as tuh, it is output as follows. Date and Time User: username Host: hostname - Страница 107 из 220
H1 ThickPaper/Heavyweight 1/Covers 1 H1B ThickPaperBack/Heavyweight 1/Covers 1 - Side 2 H2 ThickPaper2/Heavyweight 2/Covers 2 H2B ThickPaper2Back/Heavyweight 2/Covers 2 - Side 2 OHP Transparency L LabelPaper/Labels C1 CoatingPaper1/Coated 1/Coated Paper 1 C1B CoatingPaper1Back/Coated 1/Coated Paper - Страница 108 из 220
2 Feed from Multipurpose Feeder 3 Use Nearest Size (Adjust to Fit) 4 Use Larger Size (Adjust to Fit) 5 Use Nearest Size (No Zoom) 6 Use Larger Size (No Zoom) -St=mode Specifies Feed Separators from. Available Feed Separators froms are as follows. auto AutoTray/Auto 1 1stTray/Tray 1 (standard - Страница 109 из 220
-Cc=mode Specifies RGB Color Correction. Available RGB Color Corrections are as follows. 0 Off 1 Photo 2 sRGB 3 Standard/ Normal 4 Presentation This option is available only for color printing. -Gc=mode Specifies RGB Gamma Correction. Available RGB Gamma Corrections are as follows. 1.0 1.0 1.4 1.4 - Страница 110 из 220
-Gg=mode Specifies Gray Guaranteed. Available Gray Guaranteed options are as follows. on On off Off This option is available only for color printing. -Ct Specifies Color Transformation. This option is available only for color printing. Example To convert the program list of the file.txt file into - Страница 111 из 220
l When there are multiple tab codes in one line, the tab position may be off as a result of automatic line feed. In such case, use the -I or -w option. l The number of columns specified by the -w option is not the actual number of printed characters. The actual number of single-byte characters to - Страница 112 из 220
A5 Feed paper from the tray loaded with A5 (148 x 210 mm). A6 Feed paper from the tray loaded with A6 (105 x 148 mm). B5 Feed paper from the tray loaded with B5 (182 x 257 mm). LT Feed paper from the tray loaded with Letter (8.5 × 11 inches). FL Feed paper from the tray loaded with Folio (8.5 × 13 - Страница 113 из 220
applications. -l=left,bottom Specifies the print position. Printing will be executed from the left and bottom of the page. The default is 0.25 inches for both left and bottom. -s=width,height Specifies the output size. Printing will be executed with the width and height in inches. -S=width Sets the - Страница 114 из 220
If the wrong font is specified, default European font of the printer can be used. If header/footer output option is specified, the font specification of header/footer is ignored. -MSI Specifies Multipurpose Feeder. -M=type Specifies Multipurpose Feeder Paper Type. Available Multipurpose Feeder - Страница 115 из 220
le Landscape ler Landscape (Rotated) se Portrait ser Portrait (Rotated) -Pon Specifies Alternate Tray. Available Alternate Trays are as follows. 0 Use Printer Settings 1 Display Message 2 Feed from Multipurpose Feeder 3 Use Nearest Size (Adjust to Fit) 4 Use Larger Size (Adjust to Fit) 5 Use - Страница 116 из 220
-Cm=mode Specifies Output Color. Available Output Colors are as follows. c Color (CMYK) k Black -Pr=mode Specifies Print Mode. Available Print Modes are as follows. hs High Speed hq High Quality -Cc=mode Specifies RGB Color Correction. Available RGB Color Corrections are as follows. 0 Off 1 Photo 2 - Страница 117 из 220
2.6 off Off -Sc=mode Specifies Screen. Available Screens are as follows. 0 Fineness 1 Gradation 2 Auto 3 For Transparency -Gg=mode Specifies Gray Guaranteed. Available Gray Guaranteed options are as follows. on On off Off This option is available only for color printing. -Ct Specifies Color - Страница 118 из 220
/usr/local/dellbin3100cn/tiff2ps2 [-d] [-D] [-Itray-input] [-t] [-r] [-n] [-l=left,bottom] [-s=width,height] [-S=width] [-E] [-Nc=copies] [Hd=position:format] [-Hffont] [-MSI] [-M=type] [-Mfo=mode] [-Pon] [-St=mode] [-Sp] [-Sb] [-Cm=mode] [-Pr=mode] [-Cc=mode] [-Gc=mode] [-Sc=mode] [Gg=mode] [-Ct] - Страница 119 из 220
FL Feed paper from the tray loaded with Folio (8.5 × 13 inches). LG Feed paper from the tray loaded with Legal (8.5 × 14 inches). EX Feed paper from the tray loaded with Executive (7.25 × 10.5 inches). MO Feed paper from the tray loaded with Monarch (3.875 × 7.5 inches). COM10 Feed paper from the - Страница 120 из 220
Sets the width of the output size in inches. The height will be calculated automatically according to the width. -E This function turns on the image enhancement function. In some cases, this option will be ignored. -Nc=copies Specifies the number of output copies (the value of copies must be a - Страница 121 из 220
BB FinePaperBack/Bond/Plain Paper 2 - Side 2 P Stationary/Plain/Plain Paper 1 PB StationaryBack/Plain/Plain Paper 1 - Side 2 H1 ThickPaper/Heavyweight 1/Covers 1 H1B ThickPaperBack/Heavyweight 1/Covers 1 - Side 2 H2 ThickPaper2/Heavyweight 2/Covers 2 H2B ThickPaper2Back/Heavyweight 2/Covers 2 - - Страница 122 из 220
Specifies Alternate Tray. Available Alternate Trays are follows. 0 Use Printer Settings 1 Display Message 2 Feed from Multipurpose Feeder 3 Use Nearest Size (Adjust to Fit) 4 Use Larger Size (Adjust to Fit) 5 Use Nearest Size (No Zoom) 6 Use Larger Size (No Zoom) -St=mode Specifies Feed Separators - Страница 123 из 220
Specifies Print Mode. Available Print Modes are as follows. hs High Speed hq High Quality -Cc=mode Specifies RGB Color Correction. Available RGB Color Corrections are as follows. 0 Off 1 Photo 2 sRGB 3 Standard/ Normal 4 Presentation This option is available only for color printing. -Gc=mode - Страница 124 из 220
2 Auto 3 For Transparency -Gg=mode Specifies Gray Guaranteed. Available Gray Guaranteed options are as follows. on On off Off This option is available only for color printing. -Ct Specifies Color Transformation. This option is available only for color printing. Example To convert the TIFF image - Страница 125 из 220
Enables the short-edge binding feature. When it is specified, the printing direction or position will be adjusted and both sides of the paper printed so that the shorter edge of the pages can be bound. This option is available only when the optional duplex module is installed on the printer. -D - Страница 126 из 220
C5 Feed paper from the tray loaded with C5 (162 x 229 mm). LP 210x900 Feed paper from the tray loaded with LP210x900 (210 x 900 mm). MxNmm Feed paper from the tray loaded with MxN mm defined by users. Possible range specified: Width: 90.0 to 215.9 mm Length: 139.7 to 355.6 mm MxNin Feed paper from - Страница 127 из 220
ur Output on the upper right corner of the paper. dl Output on the lower left corner of the paper. dr Output on the lower right corner of the paper. format specifies the contents and the order to output. This option is omissible. If this option is omitted, uh is specified as the default value. u - Страница 128 из 220
L LabelPaper/Labels C1 CoatingPaper1/Coated 1/Coated Paper 1 C1B CoatingPaper1Back/Coated 1/Coated Paper 1 - Side 2 C2 CoatingPaper2/Coated 2/Coated Paper 2 C2B CoatingPaper2Back/Coated 2/Coated Paper 2 - Side 2 E Envelope If this option is not specified, Multipurpose Feeder Paper Type of the - Страница 129 из 220
-St=mode Specifies Feed Separators from. Available Feed Separators from the following. auto AutoTray/Auto 1 1stTray/Tray 1 (standard 250-sheet tray module) 2 2ndTray/Tray 2 (optional 250-sheet tray module or 500-sheet tray module) off Off -Sp Specifies Printed Separators -Sb Specifies Skip Blank - Страница 130 из 220
Standard/ Normal 4 Presentation This option is available only for color printing. -Gc=mode Specifies RGB Gamma Correction. Available RGB Gamma Corrections are as follows. 1.0 1.0 1.4 1.4 1.8 1.8 2.2 2.2 2.6 2.6 off Off -Sc=mode Specifies Screen. Available Screens are as follows. 0 Fineness 1 - Страница 131 из 220
Example To convert the XWD image into the PostScript language program and output it to a file, type as follows. % xwd2ps2 file.xwd > file.ps To output the XWD image to a printer, type as follows. % xwd2ps2 file.xwd | lpr (for Linux) % xwd2ps2 file.xwd | lp (for Solaris/HP-UX) Important l When -s - Страница 132 из 220
that the shorter edge of the pages can be bound. This option is available only when the optional duplex module is installed on the printer. -D Enables the long-edge binding feature. When it is specified, the printing direction or position will be adjusted and both sides of the paper printed so that - Страница 133 из 220
-Pr=mode Specifies Print Mode. -Cc=mode Specifies RGB Color Correction. This option is available only for color printing. -Gc=mode Specifies RGB Gamma Correction. -Sc=mode Specifies Screen. -Gg=mode Specifies Gray Guaranteed. This option is available only for color printing. -Ct Specifies Color - Страница 134 из 220
l To install UX filter into the default directory (/usr/local/dellbin3100cn), it's necessary to create /usr/local directory in advance. HP-UX l The printer to specify as an output printer must be registered in your system. To register an output printer, use sam command and so on. See the HP-UX - Страница 135 из 220
l If the same option is specified, or if s, S are both specified, the one specified later will prevail. l If the size option (s, S) is not specified, scaling will be executed taking one pixel of the image data as one pixel of the printer. l If the print position option (-l left bottom) specifies a - Страница 136 из 220
TBCPFilter (Solaris/Linux/HP-UX) l Make sure the TBCPFilter is available so the printer can specify the availability of the TBCPFilter. As for libtiff Copyright ©1988-1997 Sam Leffler Copyright © 1991-1997 Silicon Graphics, Inc. THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, - Страница 137 из 220
Operator Panel Using the Operator Panel Buttons Printing a Panel Settings Page Using the Operator Panel Buttons The printer operator panel has a 2-line by 16-character liquid crystal display (LCD), seven buttons, and two indicators that flash when the printer is ready to print, and when a error - Страница 138 из 220
- Страница 139 из 220
Printer Specifications OS Compatibility Dimensions Memory Page-description Language (PDL)/Emulation, Operating System, and Interface Cartridge and Printer Life Environmental Cables OS Compatibility Compatible with Windows® (XP/Me, 2000, Server 2003, NT 4.0/9x); Novell® (3.x, 4.x, 5.x, 6.x) but not - Страница 140 из 220
Interfaces Standard local: USB, IEEE 1284 Standard network: 10/100Base-Tx Ethernet MIB Compatibility A Management Information Base (MIB) is a database containing information about network devices (such as adapters, bridges, routers, or computers). This information helps network administrators - Страница 141 из 220
1 Parallel (IEEE 1284) 2 USB 3 10/100Base-Tx Ethernet CAT-5E USB2.0 - Страница 142 из 220
Understanding Printer Messages The printer operator panel displays messages describing the current state of the printer and indicates possible printer problems you must resolve. This topic provides a list of all printer messages, explains what they mean, and tells you how to clear the messages. 1 - Страница 143 из 220
Paper Jam Tray 2 072-101 Open Feed2 Cover Pull out Tray 2 004-312 TRAY1 must be 250 sheet tray Contact Support The printer detects an incorrect configuration of the trays. Transparency 077-131 Open Reg Cover Remove Paper The printer detects jammed transparencies. Turn off the printer. Set the trays - Страница 144 из 220
077-300 Front or Top Cover Is Open XXX is one of the following: · Reg Cover · BTR Cover · Paper Cover · Feeder 1 · Feeder 2 · Duplex Cover Close XXX NNN-NNN YYY Is Open YYY is one of the following: · Reg Cover · BTR Cover · Paper Cover · Feeder 1 Cover · Feeder 2 Cover · Duplex Cover Error NNN-NNN - Страница 145 из 220
· Magenta Toner · Black Toner Error NNN-NNN relates to printer problems. Ready to Print 091-402 Drum Cartridge Replace Soon Drum life warning. Replace the drum cartridge. The drum cartridge needs to be replaced. See "Replacing the Drum Cartridges" Ready to Print 193-700 non-DELL Toner Installed The - Страница 146 из 220
Connecting Your Printer Choosing the Right Cable Connecting the Printer Locally Connecting the Printer to the Network Choosing the Right Cable Your Dell Laser Printer 3100cn interconnection cable must meet the following requirements: Connection Cable certification Parallel Parallel IEEE 1284 USB - Страница 147 из 220
A local printer is a printer attached to your computer using a USB or parallel cable. If your printer is attached to a network instead of your computer, skip this step and go on to "Connecting the Printer to the Network." Microsoft® Windows® 98 SE, Windows Me, Windows 2000, Windows XP, Windows - Страница 148 из 220
To attach the printer to a network: 1. Make sure the printer, computer, and any other attached devices are turned off and unplugged. 2. Plug one end of a standard category 5 cable into a LAN drop or hub, and the other end into the Ethernet port on the back of the printer. The printer automatically - Страница 149 из 220
NOTE: Do not continue with this procedure until you have the following three addresses: - IP Address - Subnet Mask Address - Gateway Address For more information on using your operator panel, see "Operator Panel." 1. Turn on the printer. The Ready to Print appears. 2. Press Menu. 3. Press until - Страница 150 из 220
Maintaining Your Printer Periodically your printer requires you to complete certain tasks to maintain optimum print quality. If several people are using the printer, you may want to designate a key operator to maintain your printer. Refer printing problems and maintenance tasks to this key - Страница 151 из 220
The Dell Supplies Management System window appears. 2. If ordering from the Web: a. b. 3. When you cannot get information from the printer automatically by two-way communication, a window that prompts you to type the Service Tag number appears. Type your Dell printer Service Tag number in the field - Страница 152 из 220
1. To open both covers on the printer, grab the notch in the front door and pull forward. Lift the top cover and push back. 2. To remove the used drum cartridge, push up the lever on the right side of the printer. 3. Grab the drum cartridge by the handle, and pull it up and out. CAUTION: Do not - Страница 153 из 220
2. To insert the drum cartridge, push up the lever on the right side of the printer. With the lever in the upright position, hold the drum cartridge by the handle, align the arrows on the drum cartridge with the corresponding arrows on the printer and guide the cartridge in until it snaps into - Страница 154 из 220
2. Pull the cleaning rod until the cleaning pad comes out of the printer. 3. Push the two tabs on the cleaning pad inward to remove the pad. 4. Hold the new cleaning pad under the cleaning rod and push it in until it clicks. 5. Push the cleaning rod back to its original position until it stops. 6. - Страница 155 из 220
7. Close the front door. NOTE: When the optional duplex module has been opened, close it. Gently pull open the multipurpose feeder cover if necessary. Replacing the Toner Cartridge CAUTION: Before performing any of the following procedures, read and follow the safety instructions in your Owner's - Страница 156 из 220
CAUTION: Do not touch inside the printer with your hands. Some parts may be hot. Installing the New Toner Cartridge 1. Make sure the color of the toner cartridge matches the slot on the toner cartridge carrier. Gently shake the cartridge to distribute the toner evenly. 2. Lift the tab up 90 degrees - Страница 157 из 220
5. Repeat steps 1 through 4 when inserting the remaining cartridges. Cleaning Inside the Printer A cleaning rod for cleaning inside the printer is installed on your printer. 1. Open the front door. 2. Pull out the slide bar that is inside the printer on the right side until it stops. The access - Страница 158 из 220
Dell Laser Printer 3100cn User's Guide Notes, Notices, and Cautions Click the links to the left for information on the features, options, and operation of your printer. For information on other documentation included with your printer, see "Finding Information." 1 Optional duplex module 2 Optional - Страница 159 из 220
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your printer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property - Страница 160 из 220
- Страница 161 из 220
Finding Information What are you looking for? Find it here · Drivers for my printer · My User's Guide Drivers and Utilities CD The Drivers and Utilities CD contains documentation and drivers for your printer. You can use the CD to uninstall/reinstall drivers or access your documentation. Readme - Страница 162 из 220
Dell Printer Configuration Web Tool Using the Dell Printer Configuration Web Tool One of the features of the Dell Printer Configuration Web Tool is the E-Mail Alert Setup, which sends you, or the key operator, an email when the printer needs supplies or intervention. If you fill out printer - Страница 163 из 220
The Printer Jobs menu contains information on Job List page and Completed Jobs page. These pages show the details of the status regarding each protocol or the print jobs. Printer Settings Change printer settings, view the operator panel remotely. Print Server Settings Use the Print Server Settings - Страница 164 из 220
Using the Dell Printer Configuration Web Tool Environment Settings for Web Browser Dell recommends configuring the environment settings for your Web browser, before using the Dell Printer Configuration Web Tool, for the following reasons. For Netscape Communicator 7.1 Setting Up the Display - Страница 165 из 220
The following items are displayed in the Top Frame. Dell Laser Printer 3100cn Displays the printer product name. IP Address: Displays the printer's IP address. Location: Displays the printer's location. The location can be changed in Basic Information on the Print Server Settings page. Contact - Страница 166 из 220
Restart printer to apply new settings. Button Submits new settings made on the Dell Printer Configuration Web Tool to the printer and reboots the printer. The old printer settings will be replaced by the new settings. Restore Settings Button Restores the old settings from before changes made. New - Страница 167 из 220
"E-Mail Alert" "SNMP" "Other Features" "Set Password" "Reset Print Server" "Copy Printer Settings" "Copy Printer Settings" "Copy Printer Settings Report" "Tray Settings" * This item is only available when the optional memory card is installed. Printer Status Use the Printer Status menu to check the - Страница 168 из 220
Location Displays the location where the printer fault occurred. Details Displays the details of the printer fault. Print Volume Purpose: To verify the number of printed pages. This page can also be displayed by clicking Print Volume in the Left Frame. Values: Printer Page Count Displays the total - Страница 169 из 220
ID Displays the job id. Job Name Displays the file name of the job being printed. Owner Displays the job owner's name. Host Name Displays the name of the host computer. Job Status Displays the status of the job being printed. Host I/F Displays the status of the host interface. Job Submitted Time - Страница 170 из 220
Basic Settings Parallel Settings Power Saver Time Displays the amount of time before the printer enters power saver mode after it finishes a print job. Error Alarm Displays whether the printer sounds an alarm when an error occurs. Job Timeout Displays specify the amount of time the printer waits to - Страница 171 из 220
Tray Settings Tray 1 Paper Type Displays the type of paper loaded in the standard 250-sheet tray. Tray 1 Paper Size Displays the size of paper loaded in the standard 250-sheet tray. Tray 2 Paper Type Displays the type of paper loaded in the optional 250-sheet tray or 500-sheet tray module. Tray 2 - Страница 172 из 220
Tray RAM Disk Specifies whether to allocate memory to the RAM Disk file system for the Secure Print and Store Print features. This item is only available when the optional memory card is installed. Substitute Tray Specifies whether or not to use another size paper when the paper that is loaded in - Страница 173 из 220
Values: Input Tray Specifies the input tray. Paper Size Specifies the default paper size. Orientation Specifies how text and graphics are oriented on the page. Duplex Print Sets duplexing as the default for all print jobs. This item is only available when the optional duplex module is installed. - Страница 174 из 220
Re-enter Password Type the new password again to confirm. NOTE: This menu sets a password to lock the operator panel. When changing the password for the Dell Printer Configuration Web Tool, click Set Password on the left frame and set the password. Printer Maintenance Printer Maintenance tab - Страница 175 из 220
The NVRAM for the network feature cannot be initialized. Values: Initialize NVRAM and restart printer. Click Start to initialize the NVRAM. Clear Storage Purpose: To clear all files that are stored as Secure and Proof Print in the RAM Disk. This item is only available when the optional memory card - Страница 176 из 220
Copy Printer Settings Report Purpose: To verify the histories of copying after turning on the printer. Print Server Settings Use the Print Server Settings menu to set the type of printer interface and necessary conditions for communications. The following tabbed pages are displayed in the top of - Страница 177 из 220
FTP SMB* 1 AppleTalk* 1 SNMP Agent Port Number Displays the port number. Simultaneous Connections Displays the number of connections received simultaneously by the client. Connection Time-Out Displays the connection timeout period. Port Status Displays the port status. Connection Time-Out Displays - Страница 178 из 220
Status Information Displays messages according to the conditions of the printer. Logical Printer Number Displays the printer number during RPrinter Mode. NOTE: An optional multi protocol card is required to display the NetWare Setup Page. E-Mail Alert Setup Page Purpose: To verify the current - Страница 179 из 220
Auto Refresh Interval Sets the time interval for refreshing the contents of the status display pages automatically from 15 to 600 seconds. NOTE: The auto refresh feature is effective for the contents of the Top Frame, Printer Status page, Job List page, and Completed Jobs page. Port Settings - Страница 180 из 220
IP Address Mode DNS 1 WINS* AutoIP Automatically sets the IP address. DHCP Uses DHCP to set the IP address. BOOTP Uses BOOTP to set the IP address. RARP Uses RARP to set the IP address. Manually Set Enables the IP address set in IP Address. IP Address Sets the IP address allocated to the printer in - Страница 181 из 220
Network Address Displays the IPX network address. NetWare Device Name* 1 Active Mode Specifies the printer name up to 47 alphanumeric characters. For PServer Mode, set the Print Server Name (Print Server Object Name). For RPrinter Mode, set the Remote Printer Name (Printer Name in Bindery and - Страница 182 из 220
Auto Master Mode Encrypt Password On Enable the Auto Master Mode. Off Disable the Auto Master Mode. On Encrypts the password. Off Does not encrypt the password. Job Time-Out Sets the timeout period from 60 to 3600 seconds. Connection Time-Out Sets the connection timeout period from 60 to 3600 - Страница 183 из 220
Purpose: To configure the detailed settings of SNMP. Values: Community Name (Read only)*1 Specifies the community name to access (read only) the data up to 31 alphanumeric characters. The original setting will remain valid if no input is made. Characters entered for community Name in previous - Страница 184 из 220
IP Filter Procedure l Enabling Printing From a Specified User The following describes the procedure to enable printing only from the "192.168.100.10" IP address. Procedures: 1. Click the first column of Access List row 1. 2. Enter "192.168.100.10" in the Address field and "255.255.255.255" in the - Страница 185 из 220
The Other Features tab includes Set Password page and Reset Print Server page. Set Password Purpose: To set or change the password that is required to access the printer setup parameters from the Dell Printer Configuration Web Tool. Set the password of the operator panel from Security Settings in - Страница 186 из 220
- Страница 187 из 220
About Your Printer The following illustrations show the standard Dell Laser Printer 3100cn, with optional duplex module, and an optional 250-sheet tray module or 500-sheet tray module. Standard printer Printer with options 1 Center output tray 5 Optional duplex module 2 Operator panel 6 Optional - Страница 188 из 220
Understanding Fonts Typefaces and fonts Bitmapped and Scalable Fonts Resident Fonts Symbol Sets Typefaces and fonts A font is a set of characters and symbols created with a distinct design. The distinct design is called a typeface. The typefaces you select add personality to a document. Well-chosen - Страница 189 из 220
In proportional (or typographic) fonts, every character can have a different width. Since proportional fonts have characters with different widths, the font size is specified in point size, not pitch. Point size refers to the height of the characters in the font. A point is defined as 1/72 inch. - Страница 190 из 220
These temporary bitmapped fonts are deleted when you turn off or reset the printer. Scalable fonts provide the flexibility of printing in many different point sizes. Your printer uses different scalable font formats for downloading fonts to the printer. PCL 6 uses Intellifont and TrueType scalable - Страница 191 из 220
CG Omega Bold CG Omega Italic CG Omega Bold Italic Garamond Antiqua Garamond Halbfett Garamond Kursiv Garamond Kursiv Halbfett Helvetica Helvetica Helvetica oblique Helvetica-Oblique Helvetica Bold Helvetica-Bold Helvetica Bold oblique Helvetica-BoldOblique Helvetica Narrow Helvetica-Narrow - Страница 192 из 220
Palatino Bold Italic Palatino-BoldItalic SymbolPS Symbol Symbol Times Roman Times-Roman Times Italic Times-Italic Times Bold Times-Bold Times Bold Italic Times-BoldItalic Times New TimesNewRomanPSMT Times New Italic TimesNewRomanPS-ItalicMT Times New Bold TimesNewRomanPS-BoldMT Times New Bold - Страница 193 из 220
Monaco NewYork Oxford Taffy MonaLisa-Recut Candid Bodoni Bodoni-Italic Bodoni-Bold Bodoni-BoldItalic Bodoni-Poster Bodoni-PosterCompressed CooperBlack CooperBlack-Italic Copperplate-ThirtyTwoBC Copperplate-ThirtyThreeBC Eurostile Eurostile-Bold Eurostile-ExtendedTwo Eurostile-BoldExtendedTwo - Страница 194 из 220
JoannaMT JoannaMT-Italic JoannaMT-Bold JoannaMT-BoldItalic LubalinGraph-Book LubalinGraph-BookOblique LubalinGraph-Demi LubalinGraph-DemiOblique Line Printer Symbol Sets A symbol set is the collection of alphabetic and numeric characters, punctuation, and special characters available in the font - Страница 195 из 220
Understanding Your Printer Software Use the Drivers and Utilities CD that came with your printer to install a combination of software programs, depending on your operating system. The following software programs can only operate on Windows. They cannot operate on Macintosh, UNIX, or Linux. Printing - Страница 196 из 220
l Print orientation and Multiple Up (document settings) l Watermarks l Font references If you want to install the printer driver with the same settings to multiple computers running the same operating system, create a setup disk in a floppy disk or in a server on the network. Using the setup disk - Страница 197 из 220
Installing the Toner and Drum Cartridges Installing the Toner Cartridge Installing the Drum Cartridge CAUTION: Before performing any of the following procedures, read and follow the safety instructions in your Owner's Manual. Installing the Toner Cartridge Install or replace the toner cartridge - Страница 198 из 220
5. To insert the toner cartridges, align the arrows on the cartridge with the corresponding arrows on the printer. Guide the cartridge in until it snaps into place and then push down the handhold to lock the cartridge in place. 6. Close the front door. NOTE: Make sure the toner cartridge is - Страница 199 из 220
2. Remove the protective sheet from the drum cartridge. 3. To insert the drum cartridge, push up the lever on the right side of the printer. With the lever in the upright position, hold the drum cartridge by the handle, align the arrows on the drum cartridge with the corresponding arrows on the - Страница 200 из 220
NOTE: After installing the drum cartridge, the printer makes an adjustment for about one to two minutes. Do not turn off the printer during this time. - Страница 201 из 220
Loading Print Media Proper print media loading helps prevent jams and ensures trouble-free printing. Before loading print media, identify the recommended print side of the print media. This information is usually on the print media package. Loading Print Media in Standard and Optional Trays - Страница 202 из 220
4. Before loading the print media, flex the sheets back and forth, and then fan them. Straighten the edges of the stack on a level surface. 5. Place the print media into the tray with the recommended print side face up. NOTE: Do not exceed the maximum fill line in the tray. Overfilling the tray may - Страница 203 из 220
Multipurpose Feeder Capacity The maximum stack height is 16 mm (0.6 in.). The multipurpose feeder can hold approximately: l 150 sheets of 75 g/m2 (20 lb) paper Print Media Dimensions The multipurpose feeder accepts print media within the following dimensions: l Width -- 90 mm to 215.9 mm (3.5 in. - Страница 204 из 220
3. Insert the print media into the feeder with the recommended print side face up. NOTE: Do not force the print media. 4. Slide the width guides until they rest lightly against the edge of the print media stack. NOTE: Be careful not to bend the print media. 5. Make sure the size and type settings - Страница 205 из 220
To load envelopes that are under 8.66 inches (220 mm) in width, insert the envelopes with the flaps open and toward the front of the printer, with the recommended print side face up. To load envelopes that are over 8.66 inches (220 mm) in width, insert the envelopes with the flaps closed and the - Страница 206 из 220
To disable tray linking, set the Paper Size and Paper Type to a unique value in each one of the trays. If all trays do not have the same type of print media when linked, you could mistakenly print a job on the wrong paper type. Using the Duplex Function Duplex printing (or two-sided printing) - Страница 207 из 220
l 20 sheets of label: or l 10 sheets of envelope Using the Support Extension The support extension is designed to prevent print media from falling from the printer after the print job is complete. Before printing a document, make sure the paper extender is fully extended. - Страница 208 из 220
Clearing Jams Careful selection of appropriate print media and proper loading allow you to avoid most jams. See "Print Media Guidelines" for more information. Avoiding Jams Identifying the Location of Paper Jams Removing Print Jams Near the Fuser Unit Removing Print Jams Near the Center Output Tray - Страница 209 из 220
CAUTION: Do not attempt to clear any jams using tools or instruments. This may permanently damage the printer. 1 Duplex module 2 Print media source 3 Duplex cover 4 Feeder cover 5 Inner rear cover (displayed Reg Cover on message) 6 Bias Transfer Roll (BTR) cover 7 Fuser cover 8 Paper cover (not - Страница 210 из 220
CAUTION: The inside of the printer on the back side is hot. 3. Press the levers on both sides and remove any jammed print media. NOTE: Never touch the outer levers located on both sides of the fuser unit, which are used to remove or install the fuser unit. 4. Return the levers to their original - Страница 211 из 220
4. Press the levers on both sides and remove any jammed print media. NOTE: Never touch the outer levers located on both sides of the fuser unit, which are used to remove or install the fuser unit. 5. Return the levers to their original positions. 6. Close the paper cover. 7. Close the BTR cover. 8. - Страница 212 из 220
3. Open the fuser cover and remove any jammed print media. 4. Push down the levers on the both sides. 5. Close the paper cover or the optional duplex module (if the duplex module is installed). Removing Print Jams From the Print Media Pickup Area NOTE: To resolve the message displayed on the - Страница 213 из 220
4. Close the inner rear cover. 5. Close the duplex module. 6. Grab the feeder cover on the back of the printer and pull down. 7. Remove any accessible print media. 8. Close the cover. When Not Using the Optional Duplex Module 1. Open the rear cover. The inner rear cover opens at the same time. 2. - Страница 214 из 220
3. Close the rear cover. 4. Grab the feeder cover on the back of the printer and pull down. 5. Remove any accessible print media. 6. Close the cover. Removing Print Jams From the Optional Duplex Module NOTE: To resolve the message displayed on the operator panel, you must clear all print media from - Страница 215 из 220
3. Close the duplex cover. 4. Grab the optional duplex module and pull back. 5. Remove any accessible print media. 6. Close the optional duplex module. Removing Print Jams From the Print Media Source NOTE: To resolve the message displayed on the operator panel, you must clear all print media from - Страница 216 из 220
3. Return the tray to its original position. Removing Print Jams From the Multipurpose Feeder Pull the jammed print media straight out of the multipurpose feeder as shown below. NOTE: To resolve the message displayed on the operator panel, you must clear all print media from the print media path. - Страница 217 из 220
Appendix Dell Technical Support Policy Contacting Dell Warranty and Return Policy Dell Technical Support Policy Technician-assisted technical support requires the cooperation and participation of the customer in the troubleshooting process and provides for restoration of the operating system, - Страница 218 из 220
Dell Laser Printer 3100cn User's Guide Finding Information Dell Printer Configuration Web Tool About Your Printer Installing the Toner and Drum Cartridges Connecting Your Printer Enterprise Console Management Modules Installing the Optional Tray Module Installing the Optional Duplex Module Print - Страница 219 из 220
l l l l l l l l l l l l l l l l l l l - Страница 220 из 220
Инструкции и руководства похожие на DELL 3100cn
![](/i/dell/28146/dell-inspiron-14-1440/cover/cover.jpg)
![](/i/dell/50777/dell-latitude-d620-atg/cover/cover.jpg)
![](/i/dell/50778/dell-latitude-d620-atg/cover/cover.jpg)
![](/i/dell/50857/dell-latitude-e6420-atg/cover/cover.jpg)
![](/i/dell/51023/dell-vostro-3500/cover/cover.jpg)
![](/i/dell/51024/dell-vostro-3500/cover/cover.jpg)
![](/i/dell/51087/dell-xps-m1530/cover/cover.jpg)
![](/i/dell/51088/dell-xps-m1530/cover/cover.jpg)
![](/i/dell/51121/dell-e1911-monitor/cover/cover.jpg)
![](/i/dell/51122/dell-e1911-monitor/cover/cover.jpg)
![](/i/dell/51123/dell-e1911-monitor/cover/cover.jpg)
![](/i/dell/51355/dell-poweredge-c5125/cover/cover.jpg)
![](/i/dell/51356/dell-poweredge-c5125/cover/cover.jpg)
![](/i/dell/64720/dell-optiplex-390-mid-2011/cover/cover.jpg)
![](/i/dell/68043/dell-optiplex-390-mid-2011/cover/cover.jpg)
![](/i/dell/68950/dell-optiplex-390-mid-2011/cover/cover.jpg)
![](/i/dell/74832/dell-optiplex-390-mid-2011/cover/cover.jpg)