Инструкция для KARCHER BR 120/250 R I BP PACK

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

     - 

10

Danger

Risk of injury if the machine is left running 
in an unattended state. Before carrying out 
any tasks on the machine, set the main key 
to "0" and remove it. Press emergency-stop 
button. Remove the battery plug.

Drain and dispose of the dirt water and 
the residual fresh water.

In case of faults that cannot be remedied 
using the table below please contact the 
customer service. 

The operator may only replace the follow-
ing vehicle flat fuses having the following 
values: 

7.5A (F1) – Control and emergency 
power supply.

30A (F3) – Lift/accessories module sup-
ply.

80A (F6) – Lift/Clean module 2 (sweep-
er).

Note

Defective pole fuses should only be re-
placed by the service center. If these fuses 
are defective, then customer service center 
has to check the usage conditions and the 
entire control system.

The control unit is located below the oper-
ating panel. To access the fuses the cover 
on the left side of the foot compartment 
must be removed in advance.

Turn out the fastening screws at the up-
per end of the cover. 

Remove cover. 

Replace fuse.

Replace cover. 

Note

The population of fuses is displayed on the 
inner side of the cover. 

The display shows the existing faults at in-
tervals of 4 seconds (example:

Fault scrubbing
funktion H1/022

If the faults continue to be displayed on the 
console even after 4 seconds, then pro-
ceed as follows: 

Bring the key switch to "0" (switch off 
the machine).

Wait till the text on the display has dis-
appeared. 

Bring the key switch back to "1" (switch 
on the machine). Carry out the trouble-
shooting measures in the given se-
quence only if the fault occurs again. At 
such times, always bring the main 
switch to the "0" position and ensure 
that the emergency-stop button is de-
pressed.

If the fault cannot be repaired, call cus-
tomer service and mention the fault 
code(s) (H1/022 in the example). 

Troubleshooting

Replace fuses

Fault indication

25

EN

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370