English-20
Setting
Default
PICTURE
BACKLIGHT
Adjusts the overall image and background brightness. Press + or - to adjust.
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be
changed.
Depends on
destination
CONTRAST
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
50
SHARPNESS
Adjusts the crispness of the image. Press + or - to adjust.
50*
2
BRIGHTNESS
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
50
HUE
Adjusts the hue of the screen. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
50
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
50*
2
COLOR TEMPERATURE
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B
levels, CUSTOM must be showing as the COLOR TEMP selection.
NOTE: When sRGB is selected in picture mode, predefi ned 6500k is set so it cannot be changed.
When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA
CORRECTION, this function cannot be changed.
10000K
COLOR CONTROL
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function cannot be
changed.
0
GAMMA CORRECTION
Select a display gamma for best picture quality.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
PROGRAMMABLE1
(except sRGB
setting)
NATIVE
Gamma correction is handled by the LCD panel.
2.2
Typical display gamma for use with a PC.
2.4
Good for video (DVD, etc.)
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the
image (S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.
MOVIE SETTINGS
NOTE: When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function
cannot be changed.
NOISE REDUCTION*
1
SCART, VIDEO, S-VIDEO inputs only
Adjusts the amount of noise reduction. Press + or - to adjust.
0*
2
TELECINE
HDMI, Y/Pb/Pr, SCART*
1
, VIDEO*
1
, S-VIDEO*
1
,
HDMI2*
1
, HDMI3*
1
, Y/Pb/Pr2*
1
inputs only
Automatically senses the sources frame rate for optimal picture quality.
AUTO*
2
ADAPTIVE CONTRAST
HDMI, Y/Pb/Pr, SCART*
1
, VIDEO*
1
, S-VIDEO*
1
,
HDMI2*
1
, HDMI3*
1
, Y/Pb/Pr2*
1
inputs only
Sets the level of adjustment for dynamic contrast.
OFF
PICTURE MODE
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1] or
[CUSTOM2]. See page 18.
Depends on
destination
RESET
Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,
CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,
COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.
-
ADJUST
AUTO SETUP
VGA, RGB/HV*
1
inputs only
Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.
-
AUTO ADJUST
VGA, RGB/HV*
1
inputs only
H Position, V Position and Phase are adjusted automatically when new timing is detected.
OFF
H POSITION
All inputs except DVI, HDMI, DPORT
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
-
V POSITION
All inputs except DVI, HDMI, DPORT
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
-
CLOCK
VGA, RGB/HV*
1
inputs only
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
-
*1: This function depends on which option board you use.
*2: Depends on signal input.
