23

PG-005_v01

  The earthing wire must be connected to the 

terminal marked with the symbol 

. The 

electrical installation supplying the hob should 

be protected with a properly selected safety 

device and, in addition, it should be equipped 

with a suitable switch enabling the current to 

be cut off in an emergency situation.

Make sure that the mains voltage corresponds to the 

●

voltage on the rating label located on the appliance 

casing.
The hob is designed to be connected to a 230 V 50 Hz 

●

AC electricity supply and should be connected to a mains 

socket equipped with a properly connected earthing 

contact. 
If the electrical installation is damaged, connecting the 

●

hob to the socket without an earthing contact will create 

the risk of electric shock.

  The installer is obliged to 

fi

 ll in the warranty 

card, which is the basis for warranty claims.

Changing the nozzles for diff erent 
type of gas 

(Fig. B)

 Nozzles can be changed only by a certi

fi

 ed 

installation technician.

The gas hob is equipped with nozzles adapted for use with 

2E (G20) gas.
Type of gas and gas pressure, as well as thermal power and 

designation of nozzles for particular burners are shown in the 

table below:

BURNER

GAS

PRESSURE

NOZZLE 

MARKING

THERMAL 
CAPACITY

LARGE

2E (G20)

3B/P (G30)

20 mbar

37 mbar

1.18

0.72

2500 W

MEDIUM

2E (G20)

3B/P (G30)

20 mbar

37 mbar

0.92

0.58

1500 W

SMALL

2E (G20)

3B/P (G30)

20 mbar

37 mbar

0.75

0.49

1000 W

1

 Remove the burner cap and crown.

2

 Unscrew the nozzle using a special spanner.

3

 Replace the nozzle with that for a new type of gas 

according to the table.

After changing the nozzles, adjust the burners (see 

“FLAME ADJUSTMENT”).

  After changing the nozzles af

fi

 x an appropriate 

label showing the new type of gas at the hob 

connecting pipe.

Technical Parameters

The technical parameters are indicated on the rating label. 

The hob is equipped with a threaded connecting pipe 

G1/2’’ used for connecting to the gas mains. In the case of 

connecting the hob to liquid gas (propane-butane) tanks the 

fi

 tting for 

∅

 8 x 1 mm hose must 

fi

 rst be screwed onto the 

connecting pipe.
The gas hob is a class 1 appliance equipped with a power 

cord with an earthing wire. It must be connected to the mains 

socket equipped with an earthed pin.
The appliance satis

fi

 es the requirements of relevant 

standards.
The appliance complies with the following directives:

Appliances burning gaseous fuels (GAD) – 90/396/EEC, 

–

93/68/EEC.

Low Voltage Directive (LVD) – 2006/95/EC. 

–

Electromagnetic Compatibility (EMC) – 2004/108/EC.

–

The product is marked with the CE symbol on the rating label.

Appliance elements 

(Fig. D)

1

 Large burner 

Ø 100 mm 

2.5 kW

2

 Medium burner 

Ø 75 mm 

1.5 kW

3

 Small burner 

Ø 55 mm 

1.0 kW

4

 Burner knobs with ignition switch

5

 Pan support

6

 Burner cap

7

 Burner crown

8

 Burner base

9

 Ignitor

10

 Flame failure safety device

Flame adjustment 

(Fig. C)

 Flame adjustment should be performed by 

a certi

fi

 ed installation technician.

1

 Light the burner and set it to the minimum 

fl

 ame  .

2

 Remove the knob from the shaft.

3

 Use a special screwdriver and adjust the 

fl

 ame by turning 

the screw inside the shaft. As a result you will obtain a small, 

uniform 

fl

 ame around the burner.

In the case of 3B/P (G30) gas the screw must be fully 

screwed in (clockwise).

4

 Replace the knob

Make sure that when the knob is turned rapidly from 

maximum   to minimum  , the 

fl

 ame does not go out.

5

 Turn off the burner by turning the knob to position  .