Chapter 24 AAA
GS2200-24 User’s Guide
212
The following table describes the labels in this screen.
Table 60
Advanced Application > AAA > RADIUS Server Setup
LABEL
DESCRIPTION
Authentication
Server
Use this section to configure your RADIUS authentication settings.
Mode
This field is only valid if you configure multiple RADIUS servers.
Select index-priority and the Switch tries to authenticate with the first
configured RADIUS server, if the RADIUS server does not respond then
the Switch tries to authenticate with the second RADIUS server.
Select round-robin to alternate between the RADIUS servers that it
sends authentication requests to.
Timeout
Specify the amount of time in seconds that the Switch waits for an
authentication request response from the RADIUS server.
If you are using index-priority for your authentication and you are
using two RADIUS servers then the timeout value is divided between the
two RADIUS servers. For example, if you set the timeout value to 30
seconds, then the Switch waits for a response from the first RADIUS
server for 15 seconds and then tries the second RADIUS server.
Index
This is a read-only number representing a RADIUS server entry.
IP Address
Enter the IP address of an external RADIUS server in dotted decimal
notation.
UDP Port
The default port of a RADIUS server for authentication is 1812. You
need not change this value unless your network administrator instructs
you to do so.
Shared Secret
Specify a password (up to 32 alphanumeric characters) as the key to be
shared between the external RADIUS server and the Switch. This key is
not sent over the network. This key must be the same on the external
RADIUS server and the Switch.
Delete
Check this box if you want to remove an existing RADIUS server entry
from the Switch. This entry is deleted when you click Apply.
Apply
Click Apply to save your changes to the Switch’s run-time memory. The
Switch loses these changes if it is turned off or loses power, so use the
Save link on the top navigation panel to save your changes to the non-
volatile memory when you are done configuring.
Cancel
Click Cancel to begin configuring this screen afresh.
Apply
Click Apply to save your changes to the Switch’s run-time memory. The
Switch loses these changes if it is turned off or loses power, so use the
Save link on the top navigation panel to save your changes to the non-
volatile memory when you are done configuring.
Cancel
Click Cancel to begin configuring this screen afresh.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
