Инструкция для ZYXEL omni.net LCD

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

Technical Reference for ZyXEL omni.net series 

 

7-6

Bandwidth On Demand (BOD) 

The function of Bandwidth On Demand (BOD) will monitor the traffic on ISDN links while in 

Multilink PPP mode. If there is light traffic on the link, one of the channels will be dropped 

automatically. On the other hand, if only one B-channel is used and data traffic is high enough, 

BOD will establish the second B-channel to increase the bandwidth of the data link. 

The wait for the second B-channel carrier is 60 seconds. If the second B channel can not be 

connected successfully the BOD will try again after 60 seconds. If the second call is connected but 

negotiation failed, the omni.net will retry three times. If a connection is still not established after the 

third try, the Multilink PPP will be disabled automatically. 

For BOD, there are four parameters to set high/low threshold and persist time. Traffic utilization is 

measured in the ISDN link. Highly compressible data may not generate enough traffic to start the 

second B-channel. Both add-persist time and subtract-persist time must be set to activate BOD. 

BOD AT Commands 

Description 

ATJAn 

Add traffic threshold for 'n' K bits per second. 'n' = 48 (default). 

ATJSn 

Subtract traffic threshold for 'n' K bits per second. 'n' = 32 (default) 

ATKAmn 

Add persist time for 'n' period in 'm' unit, n = 0-127, m = s for seconds and m for 
minutes. 

ATKSmn 

Subtract persist time for 'n' period in 'm' unit, n = 0-127, m = s for seconds and m for 
minutes. 

Table 40. BOD AT Commands

BACP/BAP 

Bandwidth Allocation Control Protocol (BACP) and Bandwidth Allocation Protocol (BAP) is used 

for call request and link drop under Multilink PPP.  

BACP is negotiated during the network phase. Without BACP/BAP, the directory numbers of both 

B-channels must be specified before dialing out. In some cases, it is not possible for the ISP to 

support more than one chassis that is capable of bundling both channels at the same time. With 

BACP/BAP, the second B-channel directory number can be obtained while requesting a call. 

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
Оглавление инструкции

Document Outline