•  Fixing the decorative telescopic flue:

Arrange the electrical power supply within the dimensions of 

the decorative flue. If your appliance is to be installed in the 

ducting version or in the version with external motor, prepare 

the air exhaust opening. Adjust the width of the support 

bracket of the upper flue (Fig.3). Then fix it to the ceiling using 

the screws 

A

 (Fig.3) in such a way that it is in line with your 

hood and respecting the distance from the ceiling indicated 

in Fig.2. Connect the flange 

C

 to the air exhaust hole using a 

connection pipe (Fig.4). Insert the upper flue into the lower 

flue. Fix the lower flue to the hood using the screws 

B

 provided 

(Fig.4), extract the upper flue up to the bracket and fix it with 

the screws 

B

 (Fig.3). To transform the hood from a ducting 

version into a filtering version, ask your dealer for the charcoal 

filters and follow the installation instructions.

•  Filtering version:

Install the hood and the two flues as described in the 

paragraph for installation of the hood in ducting version. To 

assemble the filtering flue refer to the instructions contained 

in the kit. If the kit is not provided, order it from your dealer 

as accessory. The filters must be applied to the suction unit 

positioned inside the hood. They must be centred by turning 

them 90 degrees until the stop catch is tripped (Fig.7).

  USE AND MAINTENANCE

•  

We recommend that the cooker hood is switched on before 

any food is cooked. We also recommend that the appliance is 

left running for 15 minutes after the food is cooked, in order 

to thoroughly eliminate all contaminated air.

The effective performance of the cooker hood depends on 

constant maintenance; the anti-grease filter and the active 

carbon filter both require special attention.

•  The anti-grease filter

 is responsible retaining the grease 

particles suspended in the air, therefore it is subject to 

clogging with variable frequency according to the use of the 

appliance.

-  To prevent the danger of possible fires, at least every 2 

months one must wash the anti-grease filters by hand using 

non-abrasive neutral liquid detergents or in the dishwasher 

at low temperatures and on short cycles.

-  After a few washes, colour alterations may occur. This does 

not give the right to claim their replacement.

•  The active carbon filters

 are used to purify the air that is 

sent back into the room and its function s to mitigate the 

unpleasant odours produced by cooking.

-  The non-regenerable active carbon filters must be replaced 

at least every 4 months. The saturation of the active charcoal 

depends on the more or less prolonged use of the appliance, 

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

-  Regenerable active charcoal filters must be washed by hand, 

with non abrasive neutral detergents, or in the dishwasher at 

a maximum temperature of 65°C (the washing cycle must be 

complete without dishware). Remove excess water without 

damaging the filter, remove the plastic parts, and let the mat 

dry in the oven for at least 15 minutes approximately at a 

maximum temperature of 100°C. To keep the regenerable 

charcoal filter functioning efficient this operation must be 

repeated every 2 months. These must be replaced at least 

every 3 years or when the mat is damaged.

•  Before remounting the anti-grease filters and the regen

-

erable active charcoal filters it is important that they are 

completely dry.

•  Clean the hood frequently, both internally and exter

-

nally, using a cloth dampened with denatured alcohol or 

neutral liquid detergents that are non abrasive.

•  

The lighting .system is designed for use during cooking 

and not for the prolonged general lighting of the room. The 

prolonged use of the lighting system significantly decreases 

the average duration of the bulbs.

•  

If the appliance is equipped with courtesy lights it is possible 

to use them for general room lighting for a prolonged amount 

of time.

•  Attention:

 the non compliance with the hood cleaning 

warnings and with the replacement and cleaning of the filters 

entails risk of fires. One therefore recommends keeping to the 

suggested instructions.

•  Replacing halogen light bulbs (Fig.8A):

To replace the halogen light bulbs 

B

, remove the glass pane 

C

 using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution:

 do not touch the light bulb with bare hands.

•  Replacing the halogen/incandescent lamps (Fig.8B):

Only use lamps of the same type and wattage installed on

 the device.

•  Commands (Fig.9) mechanical

 the key symbols are ex-

plained below:

A

=

 LIGHT

B

=

 OFF

C

=

 SPEED I

D =

 SPEED II

E

=

 SPEED III.

•  Commands (Fig.10) luminous

the key symbols are ex-

plained below:

A =

 LIGHT

B

=

 OFF

C

=

 SPEED I

D =

 SPEED II

E

=

 SPEED III

F  =

 AUTOMATIC STOP TIMER - 15 minutes 

(*)

If your appliance does not have the 

INTENSIVE

 speed 

function, press key 

E

 for two seconds and it will be activated 

for 10 minutes after which it will return to the previously set 

speed. When the function is active the LED flashes. To interrupt 

it before the 10 minutes have expired press key 

E 

again.

By pressing key 

F 

for two seconds (with the hood switched 

off) the “

clean air

” function is activated. This function switches 

the appliance on for ten minutes every hour at the first speed. 

As soon as this function is activated the motor starts up at the 

first speed for ten minutes. During this time key 

F 

and key 

C 

must flash at the same time. After ten minutes the motor 

switches off and the LED of key 

F 

remains switched on with 

a fixed light until the motor starts up again at the first speed 

after fifty minutes and keys 

F 

and 

C 

start to flash again for ten 

minutes and so on. By pressing any key for the exclusion of 

the hood light the hood will return immediately to its normal 

functioning (e.g. if key 

D

 is pressed the “

clean air

” function is 

deactivated and the motor moves to the 2nd speed straight 

away. By pressing key 

B 

the function is deactivated).

(*)

 The “

AUTOMATIC STOP TIMER

” delays stopping of the 

hood, which will continue functioning for 15 minutes at the 

operating speed set at the time this function is activated.

•  Active carbon/grease filter saturation:

- When  button 

A

 flashes at a frequency of 

2 seconds

, the 

- 6 -