![background image](/i/zelmer/153116/zelmer-maestro-13z012/h/zelmer-maestro-13z012-091.png)
95
Specially designated liquids or tablets.
●
Notice
: For liquids and tablets, follow the instructions
shown on the packaging of these products.
Descaling the espresso machine
Warning
: Ensure that the espresso machine
is switched off and the connecting cord is
disconnected from the socket.
1. Take out the water tank and rinse it clean.
Depending on the descaling agent used,
follow the steps below:
A. Espresso machine descaling tablets
Pour about 1l of warm water into the
water tank and put in a suitable number
of descaling tablets, as recommended
by the manufacturer. When the
tablets have dissolved (it takes about
5-7 minutes), replace the tank.
B. Descaling liquid
Pour about 1.5l of warm water into the
water tank. Add a suitable amount of the
descaling agent, as recommended by
the manufacturer and replace the tank.
If the filter holder is in the brew head unit, take
●
it out, rinse thoroughly under running water
and put it aside.
Using a screwdriver, unscrew the filter from
●
the bottom of the filter holder unit.
Take out the filter, the washer, the screw, and
●
the seal and put them aside in a safe place.
Important:
Be careful not to lose the filter,
the washer, the screw or the seal after
disassembling the brew head unit.
Using a small delicate brush, clean the brewing
●
area of the head removing all coffee particles.
Place a sufficiently big container under the
●
brew head unit.
Insert the plug of the connecting cord in the
●
mains socket and switch on the espresso
machine by pressing button .
Warning
: Remember that if an inscription
saying
„READY
does not show on the display,
it means that the espresso machine is in the
course of reaching the operating temperature.
The moment the espresso machine has
reached the right temperature, the line of the
temperature indicator on the display will stop
flashing, symbol and an inscription saying
“READY”
will show. This indicates that the
espresso machine has reached the right
temperature and is ready to use.
Turn the regulator knob to the espresso
●
position and allow half of the decaling solution
to flow through the brew head unit.
Important
: Do not run the descaling solution
through the steam wand.
Warning
: Depending on the size of the
container under the brew head unit, it may be
necessary to empty it during the process.
Turn the knob to position
●
0
to stop the flow
(after about half of the solution has flowed
through), next press button to switch the
appliance off.
Leave the espresso machine for about 10-15
●
minutes allowing the descaling agent to work.
Next press button
●
. The espresso machine
will be switched on.
Turn the regulator knob to the espreso
●
position and allow the next portion of the
descaling solution to flow through the brew
head unit.
Take out the water tank from the appliance
●
and rinse it thoroughly under running water.
Check that all traces of the descaling solution
have been removed. Fill up the water tank
with clean water and replace it in the espresso
machine
(1) (2) (3) (4) (5)
.
Press button
●
to switch the espresso
machine on, turn the regulator knob to the
espresso
position. Run all the clean water
through the head. Repeat the process twice.
Warning
: Depending on the size of the
container under the brew head unit, it may be
necessary to empty it during the process.
When the process has finished, remove the
●
container from under the brew head and wipe
the whole brew head unit thoroughly.
Carefully install the rubber seal, the filter, and
●
the washer in the brew head, following their
disassembling procedure in reverse order.
Using a screwdriver, tighten the fastening
screw home.
Fill up the tank with fresh water and replace
●
it in the espresso machine. The appliance is
ready for further use.
GW13-023_v02