Инструкция для ZYXEL GS3700-48

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 Chapter 15 Link Aggregation

GS3700/XGS3700 Series User’s Guide

143

15.6  Static Trunking Example

This example shows you how to create a static port trunk group for ports 2-5. 

1

Make your physical connections - make sure that the ports that you want to belong to the trunk 
group are connected to the same destination. The following figure shows ports 2-5 on switch A 
connected to switch B.

Figure 88   

Trunking Example - Physical Connections

2

Configure static trunking - Click Advanced Application > Link Aggregation > Link 
Aggregation Setting
. In this screen activate trunk group T1, select the traffic distribution 
algorithm used by this group and select the ports that should belong to this group as shown in the 
figure below. Click Apply when you are done.

LACP Active

Select this option to enable LACP for a trunk.

Port

This field displays the port number. 

*

Settings in this row apply to all ports.

Use this row only if you want to make some settings the same for all ports. Use this row first 
to set the common settings and then make adjustments on a port-by-port basis. 

Note: Changes in this row are copied to all the ports as soon as you make them.

LACP Timeout

Timeout is the time interval between the individual port exchanges of LACP packets in order 
to check that the peer port in the trunk group is still up. If a port does not respond after 
three tries, then it is deemed to be “down” and is removed from the trunk. Set a short 
timeout (one second) for busy trunked links to ensure that disabled ports are removed from 
the trunk group as soon as possible. 

Select either 1 second or 30 seconds.

Apply

Click Apply to save your changes to the Switch’s run-time memory. The Switch loses these 
changes if it is turned off or loses power, so use the Save link on the top navigation panel to 
save your changes to the non-volatile memory when you are done configuring.

Cancel

Click Cancel to begin configuring this screen afresh.

Table 64   

Advanced Application > Link Aggregation > Link Aggregation Setting > LACP  (continued)

LABEL

DESCRIPTION

A

B

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
Оглавление инструкции

Document Outline