89
Synchronizing with an External Device
Time Code Signal Input
An external SMPTE-standard LTC timing signal received from the TIME
CODE terminal will be recorded as the time code. The user bit of the
external timing signal can also be recorded. Before connecting the device,
set the TIME CODE terminal to input. Also, you must set the running
mode of the time code to [Free Run] (
A
1 Open the [TC In/Out] submenu.
[
¤
TC/UB Setup]
>
[Time Code]
>
[TC In/Out]
2 Select [In] and then press SET.
Recording the User Bit of an External Signal
The user bit of an external time code signal can also be recorded with the
time code itself.
1 Open the user bit [Rec Mode] submenu.
[
¤
TC/UB Setup]
>
[User Bit]
>
[Rec Mode]
2 Select [External] and then press SET.
NOTES
• The Genlock signal synchronization stabilizes after approximately 10 seconds. When the camera locks on an
external Genlock signal,
U
will appear on the upper right of the screen.
• If the external Genlock signal is incorrect or there is no input signal, the external time code that is recorded
may be incorrect.
• While a time code signal is being received, the external time code’s drop-frame bit will be used (if the external
time code is non-drop frame, [NDF] will appear on the rear panel).
• When an external time code signal is received, the camera’s own time code will be synchronized to it and the
synchronization will be maintained even if you disconnect the cable from the TIME CODE terminal. However,
performing any of the following actions while the cable is not connected will cause the synchronization to be
disrupted; the correct time code will be restored once you reconnect the cable.
- Turning the camera off/on
- Changing the operating mode to
mode
- Changing the video configuration
• If the external time code signal is incorrect or there is no input signal, the internal time code set in the
[
¤
TC/UB Setup]
>
[Time Code] submenu will be recorded instead.
• When the camera locks on an external time code signal, [EXT-LOCK] appears on the rear panel.
Operating modes:
[
¤
TC/UB Setup]
[Time Code]
[TC In/Out]
[In]
[
¤
TC/UB Setup]
[User Bit]
[Rec Mode]
[Internal]
COP
Y
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
