![background image](/i/loewe/153202/loewe-reference-ld-46-reference-id-40-reference-ld-55/h/loewe-reference-ld-46-reference-id-40-reference-ld-55-026.png)
Reference ID 40-55
- 26 -
User guide
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
5634
Select and adapt settings for the DiSEqC
multiswitch.
OK
Adopt settings.
Repeat rate The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
Control
voltage
The control voltage controls the switching of the
polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g., control of single LNBs via
DiSEqC multiswitch).
22kHz signal The 22 kHz signal controls the switching between
high and low band in the
Band
setting. The
Position
setting controls the selection of the satellites in non-
DiSEqC capable components.
Toneburst The Toneburst controls the selection of the satellites
in non-DiSEqC but Toneburst capable components
with the
Position
and
Option
settings.
Conclude this step (for navigation refer to page 16).
5634
Mark
Satellite 1
...
Satellite 4
,
5634
Select satellite.
OK
Adopt settings.
Conclude this step (for navigation refer to page 16).
With the refresh rate you determine how often a DiSEqC command is output. This is only
necessary in a cascaded system. Your system provider will bei able to tell you more about this.
Note: The newly selected parameter in each case must be confirmed with the button.
Settings DiSEqC multiple switch
Repeat rate
none
1 2
Control voltage 13 / 18V
off
on
22kHz signal Band Position
off
Toneburst
off
Position Option
OK
Back with Proceed with
DiSEqC
multiple
switch
None
ASTRA1
19,2°E
Intelsat10-02 1°W
Türksat 42°E
Eutelsat W2 16°E Atlantic Bird3 5°W
Hellas
Sat2
39°E
Hot
Bird
13°E Telecom2C
5°W
Eutelsat
W4
36°E
Eurobird
9A
9°E Nilesat
7°W
Eurobird1
28,5°E
Eutelsat
W3A
7°E
Atlantic
Bird2
8°W
ASTRA2
28,2°E
Sirius2/3
5°E
Telecom2D
8°E
ASTRA3
23,5°E
Thor2/3
0,8°W
Atlantic
Bird1
12,5°W
Select satellites
Please select satellite 1 to satellite 4.
Satellite 1
Satellite 2 Satellite 3 Satellite 4
Back with Proceed with
Satellite
selection
n
Initial installation
.
5634
Set LNB frequencies.
Normally, you do not need to change the values.
OK
Adopt settings.
Conclude this step (for navigation refer to page 16).
(Proceed with
Setting options for DVB-S reception
(continued)
on page
LNB frequencies
Please select the LNB frequencies for both High and Low Bands.
Note: The newly selected parameter in each case must be confirmed with the button.
ASTRA1 19,2°E low band
9750 MHz
10000 MHz 10200 MHz 10600 MHz
ASTRA1 19,2°E high band
10600 MHz
10750 MHz 11000 MHz 11250 MHz
Hot Bird 13°E low band
9750 MHz
10000 MHz 10200 MHz 10600 MHz
Hot Bird 13°E high band
10600 MHz
10750 MHz 11000 MHz 11250 MHz
Eutelsat W2 16°E low band
9750 MHz
10000 MHz 10200 MHz 10600 MHz
Eutelsat W2 16°E high band
10600 MHz
10750 MHz 11000 MHz 11250 MHz
Türksat 42°E low band
9750 MHz
10000 MHz 10200 MHz 10600 MHz
Türksat 42°E high band
10600 MHz
10750 MHz 11000 MHz 11250 MHz
OK
Back with Proceed with
LNC
frequencies