![background image](/i/loewe/153202/loewe-reference-ld-46-reference-id-40-reference-ld-55/h/loewe-reference-ld-46-reference-id-40-reference-ld-55-123.png)
Reference ID 40-55
- 123 -
User guide
Antenna DVB
Here you can make settings for the DVB-T antenna and call the antenna
wizard for the DVB-S antenna.
Call Antenna DVB
HOME:
Call
Home
view.
3456
Mark
System settings
,
OK
call System settings.
65
Mark
Connections
,
4
go to next column.
65
Mark
Antenna DVB
,
4
go to next column.
65
Select the desired setting,
4
call.
Explanations of the setting options in the antenna DVB menu:
Antenna
DVB-S
Here the antenna wizard starts guiding you through
all the settings relevant to the DVB-S antenna. The
settings of the DVB-S antenna wizard are explained
in the procedure of initial installation (starting from
page 24).
Antenna
DVB-T
Here you can set whether your DVB-T antenna needs
a supply voltage.
Antennas with an integrated amplifier need a supply
voltage on the antenna line. In this case, select
Sup-
ply voltage 5V
and confirm with
OK
.
Otherwise, select
No supply voltage
and confirm
also with
OK
.
Positioning/aligning DVB-T antenna
If you are receiving one or more DVB-T stations with picture and sound
interference then you should change the installation location and
alignment of the antenna. Ask your dealer to tell you which channels
are used to broadcast the DVB-T stations in your region.
A DVB-T station is received and selected.
Calling manual search (see page 93).
Due to the preset stations, the signal source is already selected as
DVB-T. Position and align the antenna so that maximum
C/N
values
and
levels
are reached (see status bar on page 93).
Search for DVB-T stations one after the other and compare values for
C/N
and
Level
. Then position/align the antenna to the weakest station
so that maximum values for
C/N
and
Level
are obtained. The value
for
BER
should be as low as possible.
Thereafter, perform an automatic search for all DVB-T stations (see
page 94).
...
Antenna DVB
Antenna
DVB-S
Antenna
DVB-T
The following antenna wizard guides you through all the necessary
settings relevant to your antenna system.
AV connection settings
In the AV connection settings menu the parameters for the AV and
AVS connection sockets can be adapted.
Calling the connections menu
HOME:
Call
Home
view.
3456
Mark
System settings
,
OK
call System settings.
65
Mark
Connections
,
4
go to next column.
65
Mark
AV connecting settings
,
4
go to next column.
65
Select the desired setting,
4
call.
Explanations of setting possibilities in the AV connecting settings
menu:
Device at
connection
AV
Indicate here whether a set and, if yes, which one is
connected to the AV socket. See connection of the
devices starting from page 127.
AV standard You set the AV standard of the connected appliance
to AV or AVS here.
Normally you leave the setting to
Automatic
. If the
standard of the connected appliance is not detected
automatically, select the right standard.
Ask your dealer or consult the operating manual of
the connected appliance if necessary.
Signal type You set the signal type of the device connected to AV
or AVS here. Normally, you should leave the setting to
Automatic SVHS/VHS
; otherwise select a suitable
signal type. You can find out more from your dealer.
Allow
switching
voltage
If this function is activated, the video and audio of an
external unit connected to the
AV
connector (not at
AVS) will immediately be reproduced on all TV broad-
cast sites when playback is started up, provided that
the external unit supplies a switching voltage.
...
AV connect-
ing settings
AV standard
Signal type
Please input whether a device is connected to the AV socket and if so, which
device.
Allow switch-
ing voltage
n
System settings
Connections