require to be replaced. Contact a service representative.
The paper keeps jamming.
There is too much paper in the tray. Remove excess paper from the tray. If you
are printing on special materials, use the manual tray.
An incorrect type of paper is being used. Use only paper that meets the
specifications required by the machine (See
There may be debris inside the machine. Open the front door and remove any
debris.
If an original does not feed into the machine, the document feeder rubber pad may
need to be replaced. Contact a service representative.
Transparencies stick
together in the paper exit.
Use only transparencies specifically designed for laser printers. Remove each
transparency as it exits from the machine.
Envelopes skew or fail to
feed correctly.
Ensure that the paper guides are against both sides of the envelopes.
Printing problems
Condition
Possible cause
Suggested solutions
The machine does not
print.
The machine is not
receiving power.
Check the power cord connections.
The machine is not
selected as the default
machine.
Select your machine as your default machine in your
Windows.
Check the machine for the following:
The front door is not closed. Close the front door.
Paper is jammed. Clear the paper jam (See
).
No paper is loaded. Load paper (See
The toner cartridge is not installed. Install the toner cartridge.
If a system error occurs, contact your service representative.
The connection cable
between the computer
and the machine is not
connected properly.
Disconnect the machine cable and reconnect it.
The connection cable
between the computer
and the machine is
defective.
If possible, attach the cable to another computer that is
working properly and print a job. You can also try using a
different cable.
The port setting is
incorrect.
Check the Windows printer setting to make sure that the
print job is sent to the correct port. If the computer has
more than one port, make sure that the machine is attached
to the correct one.
The machine may be
configured incorrectly.
Check the
Printing Preferences
to ensure that all of the
print settings are correct (See
The printer driver may be
incorrectly installed.
Repair the machine software (See
Installing network connected machine’s
The machine is
malfunctioning.
Check the display message on the control panel to see if the
machine is indicating a system error. Contact a service
representative.
The machine does not
print.
The document size is so
big that the hard disk
space of the computer is
insufficient to access the
print job.
Get more hard disk space and print the document again.
The output tray is full.
Once the paper is removed from the output tray, the
machine resumes printing.
The machine selects
print materials from the
wrong paper source.
The paper option that
was selected in the
Printing Preferences
may be incorrect.
For many software applications, the paper source selection is
found under the Paper tab within the
Printing Preferences
.
Select the correct paper source. See the printer driver help
screen (See
).
A print job is extremely
The job may be very
Reduce the complexity of the page or try adjusting the print
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
Инструкции и руководства похожие на DELL 1135n
