Printing Network Configuration report
You can print a
Network Configuration Report
from the machine’s control panel that will show the current
machine’s network settings. This will help you to set up a network and troubleshoot problems.
1.
Press
Menu
(
) on the control panel.
2.
Press the left/right arrow until
Network
appears and press
OK
.
3.
Press the left/right arrow until
Network Info.
appears and press
OK
.
4.
Press the left/right arrow until
Yes
appears and press
OK
.
Using this
Network Configuration Report
, you can find your machine MAC address and IP address.
For example:
MAC Address:00:15:99:41:A2:78
IP Address:192.0.0.192
Setting IP address
First, you have to set up an IP address for network printing and managements. In most cases a new IP address will
be automatically assigned by a DHCP (Dynamic Host Configuration Protocol) server located on the network.
In a few situations the IP address must be set manually. This is called a static IP and is often required in corporate
Intranets for security reasons.
DHCP IP assignment
: Connect your machine to the network, and wait a few minutes for the DHCP server to
assign an IP address to the machine. Then, print the
Network Configuration Report
as explained above. If the
report shows that the IP address has changed, the assignment was successful. You will see the new IP address in
the report.
Static IP assignment
: Use SetIP program to change the IP address from your computer. If your machine has a
control panel, you can also change IP address using the machine's control panel.
In an office environment, we recommend that you contact a network administrator to set this address for you.
IP setting using control panel
1.
Connect your machine to the network with a network cable.
2.
Turn on the machine.
3.
Press
Menu
(
) on the control panel.
4.
Press the left/right arrow until
Network
appears and press
OK
.
5.
Press the left/right arrow until
TCP/IP (IPv4)
appears and press
OK
.
6.
Press the left/right arrow until
Static
appears and press
OK
.
7.
Press the left/right arrow until
IP Address
appears and press
OK
.
8.
Enter the IP address using numeric keypad and press
OK
.
Enter a byte between 0 and 255 using the number keypad and press the left/right arrow to move
between bytes.
Repeat this to complete the address from the 1st byte to the 4th byte.
9.
Enter other parameters, such as the
Subnet Mask
and
Gateway
appears and press
OK
.
10.
After entering all parameters, press
Stop/Clear
to return to ready mode.
Installing network connected machine’s driver
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your machine using its MAC address to
communicate with the machine. A MAC address is the hardware serial number of the network interface and can
be found in the
Network Configuration Report
.
For using SetIP program, disable the computer firewall before continuing by performing the following:
1.
Open
Control Panel
.
2.
Double click
Security Center
.
3.
Click
Windows Firewall
.
4.
Disable the firewall.
Installing the program
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
