Reference ID 40-55

- 123 -

User guide

Antenna DVB

Here you can make settings for the DVB-T antenna and call the antenna 
wizard for the DVB-S antenna.

Call Antenna DVB

HOME: 

Call 

Home

 view.

3456

Mark

 System settings

, 

OK

 call System settings.

 65

Mark 

Connections

, 

4

  go to next column.

 65

Mark

 Antenna DVB

, 

4

  go to next column.

 65

 Select the desired setting,

 4

 call.

Explanations of the setting options in the antenna DVB menu:

Antenna 

DVB-S

Here the antenna wizard starts guiding you through 
all the settings relevant to the DVB-S antenna. The 
settings of the DVB-S antenna wizard are explained 
in the procedure of initial installation (starting from 
page 24).

Antenna 

DVB-T

Here you can set whether your DVB-T antenna needs 
a supply voltage. 
Antennas with an integrated amplifier need a supply 
voltage on the antenna line. In this case, select 

Sup-

ply voltage 5V

 and confirm with 

OK

. 

Otherwise, select 

No supply voltage

 and confirm 

also with 

OK

.

Positioning/aligning DVB-T antenna

If you are receiving one or more DVB-T stations with picture and sound 
interference then you should change the installation location and 
alignment of the antenna. Ask your dealer to tell you which channels 
are used to broadcast the DVB-T stations in your region.

A DVB-T station is received and selected.
Calling manual search (see page 93).

Due to the preset stations, the signal source is already selected as 
DVB-T. Position and align the antenna so that maximum 

C/N

 values 

and 

levels

 are reached (see status bar on page 93). 

Search for DVB-T stations one after the other and compare values for 

C/N

 and 

Level

. Then position/align the antenna to the weakest station 

so that maximum values for 

C/N

 and 

Level

 are obtained. The value 

for 

BER 

should be as low as possible.

Thereafter, perform an automatic search for all DVB-T stations (see 
page 94).

...

Antenna DVB

Antenna

DVB-S

Antenna 

DVB-T

The following antenna wizard guides you through all the necessary 

settings relevant to your antenna system.

AV connection settings

In the AV connection settings menu the parameters for the AV and 
AVS connection sockets can be adapted.

Calling the connections menu

HOME: 

Call 

Home

 view.

3456

Mark

 System settings

, 

OK

 call System settings.

 65

Mark 

Connections

, 

4

  go to next column.

 65

Mark

 AV connecting settings

, 

4

  go to next column.

 65

 Select the desired setting,

 4

 call.

Explanations of setting possibilities in the AV connecting settings 
menu:

Device at 

connection 

AV

Indicate here whether a set and, if yes, which one is 
connected to the AV socket. See connection of the 
devices starting from page 127.

AV standard You set the AV standard of the connected appliance 

to AV or AVS here. 
Normally you leave the setting to 

Automatic

. If the 

standard of the connected appliance is not detected 
automatically, select the right standard. 
Ask your dealer or consult the operating manual of 
the connected appliance if necessary.

Signal type You set the signal type of the device connected to AV 

or AVS here. Normally, you should leave the setting to 

Automatic SVHS/VHS

; otherwise select a suitable 

signal type. You can find out more from your dealer. 

Allow 

switching 

voltage

If this function is activated, the video and audio of an 
external unit connected to the 

AV

 connector (not at 

AVS) will immediately be reproduced on all TV broad-
cast sites when playback is started up, provided that 
the external unit supplies a switching voltage.

...

AV connect-

ing settings

AV standard

Signal type

Please input whether a device is connected to the AV socket and if so, which

device.

Allow switch-

ing voltage

n

System settings
Connections