Chapter 12 AP Profile
NWA3000-N Series User’s Guide
153
Rate Configuration This section controls the data rates permitted for clients.
For each
Rate
, select a rate option from its list. The rates are:
•
Fast Select
- Select an 802.11 broadcast frequency to determine
the baseline rate configuration.
•
Basic Rate (Mbps)
- Set the basic rate configuration in Mbps.
•
Support Rate (Mbps)
- Set the support rate configuration in
Mbps.
•
MCS Rate
- Set the MCS rate configuration.
WDS Settings
This section displays if you set the
Operating Mode
to
AP+Bridge
or
Bridge/Repeater
. Configure the security settings for the
NWA3000-N series AP’s Wireless Distribution System (WDS), the
wireless connection between two or more APs.
Select
No Security
to not encrypt the traffic between APs.
Note: WDS security is independent of the security settings
between the NWA3000-N series AP and any wireless
clients.
Select
TKIP (ZyAIR Series Compatible)
to enable Temporal Key
Integrity Protocol (TKIP) security on your WDS. This option is
compatible with other ZyXEL access points that support WDS
security. Use this if the other access points on your network support
WDS security but do not have an AES option.
Note: Check your other AP’s documentation to make sure it
supports WDS security.
Select
AES
to enable Advanced Encryption System (AES) security on
your WDS. AES provides superior security to TKIP. Use AES if the
other access points on your network support it for the WDS.
Note: At the time of writing, this option is compatible with other
ZyXEL NWA access points only.
When you enable WDS security, for each access point in your WDS
enter the AP’s MAC address and a pre-shared key. Each access point
can use a different pre-shared key. Configure WDS security and the
relevant PSK in each of your other access point(s).
Note: Other APs must use the same encryption method to
enable WDS security.
Edit
Click this to edit the selected entry.
Activate
To turn on an entry, select it and click
Activate
.
Inactivate
To turn off an entry, select it and click
Inactivate
.
#
This field is a sequential value, and it is not associated with a specific
user.
Status
This field shows whether or not the entry is activated.
Table 53
Configuration > Object > AP Profile > Add/Edit Profile (continued)
LABEL
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
