Инструкция для ZYXEL NWA3550-N

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 Chapter 21 Troubleshooting

NWA3000-N Series User’s Guide

277

Wireless clients are not being load balanced among my APs.

• Make sure that all the APs used by the wireless clients in question share the 

same SSID, security, and radio settings.

• Make sure that all the APs are in the same broadcast domain.
• Make sure that the wireless clients are in range of the other APs; if they are only 

in range of a single AP, then load balancing may not be as effective.

In the 

Monitor > Wireless > AP Information > Radio List

 page, there is no load 

balancing indicator associated with any APs assigned to the load balancing task.

• Check to be sure that the AP profile which contains the load balancing settings is 

correctly assigned to the APs in question.

• The load balancing task may have been terminated because further load 

balancing on the APs in question is no longer required.

21.6  Resetting the NWA3000-N series AP

If you cannot access the NWA3000-N series AP by any method, try restarting it by 
turning the power off and then on again. If you still cannot access the NWA3000-N 
series AP by any method or you forget the administrator password(s), you can 
reset the NWA3000-N series AP to its factory-default settings. Any configuration 
files or shell scripts that you saved on the NWA3000-N series AP should still be 
available afterwards.

Use the following procedure to reset the NWA3000-N series AP to its factory-
default settings. This overwrites the settings in the startup-config.conf file with 
the settings in the system-default.conf file. 

Note: This procedure removes the current configuration. 

1

Make sure the 

PWR\SYS

 LED is on and not blinking.

2

Press the 

RESET

 button and hold it until the 

PWR\SYS

 LED begins to blink. (This 

usually takes about five seconds.)

3

Release the 

RESET

 button, and wait for the NWA3000-N series AP to restart.

You should be able to access the NWA3000-N series AP using the default settings.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
Оглавление инструкции

Document Outline