Prestige 334 User’s Guide
Chapter 23 Remote Node Configuration
230
23.4 Remote Node Filter
Move the cursor to the field
Edit Filter Sets
in menu 11.1, and then press
[SPACE BAR]
to
set the value to
Yes
. Press
[ENTER]
to open
Menu 11.5 - Remote Node Filter
.
Use
menu 11.5 to specify the filter set(s) to apply to the incoming and outgoing traffic between
this remote node and the Prestige to prevent certain packets from triggering calls. You can
specify up to 4 filter sets separated by commas, for example, 1, 5, 9, 12, in each filter field.
Note that spaces are accepted in this field. For more information on defining the filters, please
refer to the Filters chapter. For
PPPoE or PPTP encapsulation, you have the additional option
of specifying remote node call filter sets.
Metric
Enter a number from 1 to 15 to set this route’s priority among the Prestige’s routes
(see the
Metric
section in the
WAN and Dial Backup Setup
chapter) The smaller the
number, the higher priority the route has.
Private
This field is valid only for PPTP/PPPoE encapsulation. This parameter determines if
the Prestige will include the route to this remote node in its RIP broadcasts. If set to
Yes
, this route is kept private and not included in RIP broadcast. If
No
, the route to
this remote node will be propagated to other hosts through RIP broadcasts.
RIP Direction
Press [SPACE BAR] and then [ENTER] to select the RIP direction from
Both
/
None
/
In Only
/
Out Only
. See the
LAN Setup
chapter for more information on RIP. The
default for RIP on the WAN side is
None
. It is recommended that you do not change
this setting.
Version
Press [SPACE BAR] and then [ENTER] to select the RIP version from
RIP-1
/
RIP-2B
/
RIP-2M
or
None
.
Multicast
IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to
establish membership in a Multicast group. The Prestige supports both IGMP version
1 (
IGMP-v1
) and version 2 (
IGMP-v2)
. Press [SPACE BAR] to enable IP Multicasting
or select
None
to disable it. See the
LAN Setup
chapter for more information on this
feature.
Once you have completed filling in
Menu 11.3 Remote Node Network Layer Options
, press [ENTER]
at the message “Press ENTER to Confirm...” to save your configuration and return to menu 11, or press
[ESC] at any time to cancel.
Table 77
Remote Node Network Layer Options
FIELD
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
