Инструкция для ZYXEL P-334 EE

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

Prestige 334 User’s Guide

Chapter 30 Firmware and Configuration File Maintenance

290

30.2.6  Backup Configuration Using TFTP

The Prestige supports the up/downloading of the firmware and the configuration file using 
TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as 
well, it is not recommended.

To use TFTP, your computer must have both telnet and TFTP clients. To backup the 
configuration file, follow the procedure shown next.

1

Use telnet from your computer to connect to the Prestige and log in. Because TFTP does 
not have any security checks, the Prestige records the IP address of the telnet client and 
accepts TFTP requests only from this address.

2

Put the SMT in command interpreter (CI) mode by entering 8 in 

Menu 24 –

 

System 

Maintenance

.

3

Enter command “sys stdio 0” to disable the SMT timeout, so the TFTP transfer will not 
be interrupted. Enter command “sys stdio 5” to restore the five-minute SMT timeout 
(default) when the file transfer is complete.

4

Launch the TFTP client on your computer and connect to the Prestige. Set the transfer 
mode to binary before starting data transfer.

5

Use the TFTP client (see the example below) to transfer files between the Prestige and the 
computer. The file name for the configuration file is “rom-0” (rom-zero, not capital o).

Note that the telnet connection must be active and the SMT in CI mode before and during the 
TFTP transfer. For details on TFTP commands (see following example), please consult the 
documentation of your TFTP client program. For UNIX, use “get” to transfer from the 
Prestige to the computer and “binary” to set binary transfer mode.

30.2.7  TFTP Command Example

The following is an example TFTP command:

tftp [-i] host get rom-0 config.rom

where “i” specifies binary image transfer mode (use this mode when transferring binary files), 
“host” is the Prestige IP address, “get” transfers the file source on the Prestige (rom-0, name of  
the configuration file on the Prestige) to the file destination on the computer and renames it 
config.rom.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
Оглавление инструкции

Document Outline