Инструкция для D-LINK DGS-3710-12C

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

DGS-3710 Series Layer 2 Managed Gigabit Switch CLI Reference Guide

275

<value 1-7> | last_member_query_interval <sec 1-25> | state [enable | disable] | version
<value 1-3>} (1)

Parameters

vlan_name

- Specifies the name of the VLAN for which IGMP snooping querier is to be

configured.

<vlan_name 32>

- Specifies the VLAN name. The maximum length is 32 characters.

vlanid

- Specifies the VLAN ID list.

<vlanid_list>

- Specifies the VLAN ID list.

all

- Specifies to configure all VLANs and VLAN IDs.

query_interval

- Specifies the amount of time in seconds between general query transmissions.

<sec 1-65535>

- Specifies the amount of time in seconds between general query

transmissions. The default setting is 125 seconds.

max_response_time

- Specifies the maximum time in seconds to wait for reports from members.

<sec 1-25>

- Specifies the maximum time in seconds to wait for reports from members. The

default setting is 10 seconds.

robustness_variable

- Provides fine-tuning to allow for expected packet loss on a subnet. The

value of the robustness variable is used in calculating the following IGMP message intervals:

•

Group member interval—Amount of time that must pass before a multicast router
decides there are no more members of a group on a network. This interval is
calculated as follows: (robustness variable x query interval) + (1 x query response
interval).

•

Other querier present interval—Amount of time that must pass before a multicast
router decides that there is no longer another multicast router that is the querier. This
interval is calculated as follows: (robustness variable x query interval) + (0.5 x query
response interval).

•

Last member query count—Number of group-specific queries sent before the router
assumes there are no local members of a group. The default number is the value of
the robustness variable.

<value 1-7>

- Specifies the value between 1 and 7. Increase the value if you expect a subnet

to be lossy. The robustness variable is set to 2 by default.

last_member_query_interval

- Specifies the maximum amount of time between group-specific

query messages, including those sent in response to leave-group messages. You might lower
this interval to reduce the amount of time it takes a router to detect the loss of the last member
of a group.

<sec 1-25>

- Specifies the time between 1 and 25 seconds.

state

- If the state is enable, it allows the switch to be selected as a IGMP Querier (sends IGMP

query packets). It the state is disabled, then the switch can not play the role as a querier. Note
that if the Layer 3 router connected to the switch provides only the IGMP proxy function but
does not provide the multicast routing function, then this state must be configured as disabled.
Otherwise, if the Layer 3 router is not selected as the querier, it will not send the IGMP query
packet. Since it will not also send the multicast-routing protocol packet, the port will be timed
out as a router port.

enable

- Allows the switch to be selected as an IGMP Querier (sends IGMP query packets).

disable

- When disabled, the switch can not play the role as a querier.

version

- Specifies the version of IGMP packet that will be sent by this port. If a IGMP packet

received by the interface has a version higher than the specified version, this packet will be
dropped.

<value 1-3>

- Specifies the values between 1 and 3. By default, the version is 2.

Restrictions

Only Administrator and Operator-level users can issue this command.